Todays Project - What did you do today?
(06-21-2022, 07:32 AM)rleete Wrote: ...  I'm surprised you didn't engine turn the plates.

Hmmm. Chin

Ed
Reply
Thanks given by:
(06-21-2022, 10:54 AM)EdK Wrote:
(06-21-2022, 07:32 AM)rleete Wrote: ...  I'm surprised you didn't engine turn the plates.

Hmmm.  Chin

Ed

They look good to me.
Reply
Thanks given by: EdK
(06-11-2022, 11:17 PM)Vinny Wrote: On my mini I put a piece of t-slot from LMS, I think it was from the micro mill or something like that.  AXA fits on it nicely and I can move it around.  And I also removed the compound.

Vinny,

Did the t-slot you got from LMS fit the dovetail spacing on the cross slide or did you have to modify it? I just got an AXA QCTP yesterday and would like to install it on the mini lathe.

Ed
Reply
Thanks given by:
Well the lathe is gone now, along with the t-slot (traded for that shear) but here's what I can tell you.

I had to drill or mill out a portion of the underside 'cuze the thing the compound turns on for angles isn't easily removable. Then in the top of the cross slide I drilled and tapped 4 holes for 1/4-20 cap screws to hold in sorta the 4 corners. I used the two existing holes on one end of the t-slot but since it was a bit too long I had to cut it off and I drilled and countered two more holes (same spacing as the existing ones) and drilled and tapped the cross slide there too. It was very solid and when I prepared the lathe to sell it, it was easy to pop off the t-slot and put the compound back on. And since the under side of the t-slot had the space milled out, there was no question how to put it back on.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by: EdK
So you basically bolted the t-slot table to the existing cross slide, is that correct?

Ed
Reply
Thanks given by:
Yes, it was just a hunk of t-slot. I'll see if I can find it on the LMS website. That's where I got it.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
I'm pretty sure it was this one:
https://littlemachineshop.com/products/p...4&category=
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by: EdK
(07-03-2022, 09:39 PM)Vinny Wrote: I had to drill or mill out a portion of the underside 'cuze the thing the compound turns on for angles isn't easily removable.

Do you mean you machined the underside to clear the boss on the rotating disk?

Ed

   
Reply
Thanks given by:
Yup, that's what I did. As you can see it won't take much cuze it doesn't stick up that far.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by: EdK
(07-04-2022, 05:29 PM)Vinny Wrote: Yup, that's what I did.  As you can see it won't take much cuze it doesn't stick up that far.

I had to do the same thing for my cast iron spacer block for my OXA QCTP.

I ordered the t-slot table from LMS.

Ed

   
Reply
Thanks given by:




Users browsing this thread: 25 Guest(s)