MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#5,281
10-30-2021, 11:34 PM
Nice, very nice.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 7 users Like f350ca's post:
TomG (01-22-2022), EdK (01-22-2022), Hawkeye (01-22-2022), Highpower (01-23-2022), arvidj (01-23-2022), Vinny (01-23-2022), rleete (01-24-2022)
#5,282
01-22-2022, 10:10 PM
Some more cellulose.
Built these for some one. 
The barrel for the coffee table was disassembled (rather violently, when I cut the bands there was considerable tension release lol) Then sanded inside and out and reassembled. The top and cradle are Butternut, now an endangered tree.
The barrel for the end tables was sandblasted, inside and out after cutting it in two. Gave a gorgeous surface finish in the white oak. The tops and legs were again Butternut.
[Image: 9kZNml4hDwJY4-2mkyPyDEZq160HQerVr0mexN6_...authuser=0]

[Image: OKzm53XshlcWAn6Nr6gJjvu-R55yNuac_DLZK4lo...authuser=0]

[Image: AJr7qDH3439U4MY3gAurTRMY9hLR0Od5hBB6sVWn...authuser=0]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#5,283
01-22-2022, 10:19 PM
Very nice, Greg.
It must be tough to let go of some of your creations.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: f350ca
Highpower Offline
JAFO
******
Posts: 4,493
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#5,284
01-23-2022, 02:22 AM
Beautiful pieces Greg. Worthy
Willie
Reply
Thanks given by: f350ca
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#5,285
01-23-2022, 10:42 AM
Beautiful craftsmanship. Well done sir.
Reply
Thanks given by: f350ca
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 7 users Like EdK's post:
JScott (06-03-2022), TomG (06-03-2022), f350ca (06-03-2022), Vinny (06-03-2022), Hawkeye (06-04-2022), arvidj (06-10-2022), Highpower (06-11-2022)
#5,286
06-03-2022, 04:46 PM
Made a t-slot cleaner for my mill.

Ed

   
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 4 users Like EdK's post:
Vinny (06-07-2022), f350ca (06-08-2022), arvidj (06-10-2022), Highpower (06-11-2022)
#5,287
06-07-2022, 01:53 PM
I finally finished up the carriage lock for the lathe. I used two pieces of brass for the nut instead of milling it from a thicker piece, which I didn't have. It appears to work well. I'll find out for sure when I actually use it on a project, but its got to work better than using the half nuts as a carriage lock.

Ed

         

   
Reply
Thanks given by:
vtsteam Offline
Sophmore
***
Posts: 205
Threads: 3
Joined: Jul 2014
Location: Vermont
#5,288
06-07-2022, 06:36 PM
Excellent!
http://www.youtube.com/c/SRHacksaw
Reply
Thanks given by: EdK
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,799
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#5,289
06-07-2022, 07:31 PM
Nice, Ed.

You may want to consider a adding a thread insert for the lock screw to make it last.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#5,290
06-07-2022, 07:53 PM
(06-07-2022, 07:31 PM)TomG Wrote: Nice, Ed.

You may want to consider a adding a thread insert for the lock screw to make it last.

Tom

Good idea Tom! Thumbsup

Ed
Reply
Thanks given by:




Users browsing this thread: 19 Guest(s)