MetalworkingFun Forum › Machining › Projects v
[PROJECT] Spin Indexer Tailstock

Thread Modes
Project Spin Indexer Tailstock
RobWilson
Unregistered
 
#41
08-22-2014, 12:19 PM
Smile Evening Ed

How did you get that chatter pattern ? Big Grin


Rob
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#42
08-22-2014, 04:43 PM
(08-22-2014, 12:19 PM)RobWilson. Wrote: Smile Evening Ed

How did you get that chatter pattern ? Big Grin


Rob

Rob,

I'm not sure I could teach anyone. It's an art that defies explanation. 17428

I'm going to have to chuck it up between centers again because the diameter is not very consistent along the length. I think I know why it happened, and the resulting chatter pattern, and will have to come up with a creative way of re-chucking it so I can cut the whole length to a consistent diameter. Chin

Ed
Reply
Thanks given by:
doubleboost Offline
Super Moderator
******
Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England
The following 1 user Likes doubleboost's post:
Mayhem (08-22-2014)
#43
08-22-2014, 04:43 PM
(08-22-2014, 12:19 PM)RobWilson. Wrote: Smile Evening Ed

How did you get that chatter pattern ? Big Grin


Rob


I will show you one day Mate Yikes
http://www.youtube.com/user/doubleboost
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#44
08-22-2014, 04:45 PM
(08-22-2014, 04:43 PM)doubleboost Wrote:
(08-22-2014, 12:19 PM)RobWilson. Wrote: Smile Evening Ed

How did you get that chatter pattern ? Big Grin


Rob


I will show you one day Mate Yikes

Rotfl
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#45
08-22-2014, 07:09 PM
Why bother with the Morse taper Ed. You'll only ever use a dead centre in it. The one for my indexing head is one piece.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#46
08-22-2014, 07:26 PM
(08-22-2014, 07:09 PM)f350ca Wrote: Why bother with the Morse taper Ed. You'll only ever use a dead centre in it. The one for my indexing head is one piece.

Ah, I need a method of holding the dead center. The MT-2 arbor does that for me. Or am I misunderstanding your comment? 17428

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#47
08-23-2014, 12:00 AM (This post was last modified: 08-23-2014, 12:03 AM by f350ca.)
The tailstock for my indexing head has the 60 deg point machined on the end of the arbor, one solid section.

[Image: IndexingHead-Tailstock.jpg]

Not mine as you can tell, far to clean
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#48
08-23-2014, 09:38 AM
OK, I understand now. That's actually how the plans show to make the center. I was concerned that it wouldn't be hardened steel but for the use it will see I doubt that would be a problem. If it gets dinged up it would be easy enough to clean it up on the lathe. Chin

Ed
Reply
Thanks given by:
RobWilson
Unregistered
 
#49
08-23-2014, 11:58 AM
Hi Ed

Doing it your way is not a bad idea as it does facilitate the use of different types of centres , half centre etc ,as sometimes when working on the very end of smaller parts the larger centre can get in the way .

Just a thought Chin


Rob
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#50
08-23-2014, 02:18 PM
Good point Rob. Chin

Since I've gotten this far with it I may as well continue on.

Ed
Reply
Thanks given by:




Users browsing this thread: 5 Guest(s)