Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
f350ca (09-30-2015)
09-30-2015, 07:33 AM
(This post was last modified: 09-30-2015, 07:34 AM by dallen.)
Darren I hate to say it but she left a long time ago.
there is no nut, the moveable jaw is dovetailed into the stationary bottom frame and is threaded for the Acme Rod that opens and closes the vise. And the vise isn't big enough to warrant putting soft jaws on it except to keep it part for part with the original that it was copied from. Jaw width by the time that its cleaned up will be around 1.8 inches, not like the owner is going to be banging on it with a sledge
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The soft jaw comment was tongue in cheek Dave, given that you have cast them out of Al 
Hunting American dentists since 2015.
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
PixMan (09-30-2015)
Tore down the scaffolding this morn. Squirrel eviction complete.
![[Image: IMG_1896.jpg]](https://lh3.googleusercontent.com/-DtuJS0lo5Xc/VgwcIHEMFII/AAAAAAAADWU/-oHJVwHzWwA/s1280-Ic42/IMG_1896.jpg)
Free advice is worth exactly what you payed for it.
Greg
Posts: 642
Threads: 14
Joined: Oct 2013
Location: East Sussex, UK
The following 1 user Likes awemawson's post:
rleete (10-01-2015)
Don't walk out of that door Greg :)
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 2 users Like dallen's post:
Mayhem (09-30-2015), PixMan (09-30-2015)
(09-30-2015, 09:41 AM)Mayhem Wrote: The soft jaw comment was tongue in cheek Dave, given that you have cast them out of Al
this ones a little harder
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
Highpower (10-02-2015)
besides making a mess in the shed doing metal casting, I've been working on this little item.
A .514 bullet sizing die for the 50/90 Rolling Block I've been working
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 2 users Like dallen's post:
Mayhem (10-03-2015), DaveH (10-03-2015)
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
video of the cast iron melt that I did today
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 4,452
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
Love the dross scraper. 
Willie
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
10-04-2015, 09:56 AM
(This post was last modified: 10-04-2015, 09:58 AM by dallen.)
my slotted spoon won't hold up in cast iron so I repurposed a worn out blade off my mower deck
shame I didn't have a pot of stew ready to stick in the beast after pouring the iron, all the heat gone to waste.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
|
