Stock racks...what do you use?
#81
Nice welds Darren.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: Mayhem
#82
(05-02-2015, 07:11 AM)EdK Wrote: Thanks for the pictures Darren. Especially that first one. I didn't realize there were two cross members at the front.

Ed

On mine, there aren't. Must be a Mayhem modification!

Nice welds indeed, and I also like the look of the wood in there.

I guess paint or powdercoating is all that is left to do?
Reply
Thanks given by: Mayhem
#83
Thanks for the comments guys Big Grin

Ed - as Ken pointed out it is a add in of mine. I wanted to keep the bottom shelf separate and adding in that cross member also gives me the anchoring point for the piece of mesh that will occupy one of the three bottom sections for odd size stock.

At first I wasn't going to worry about putting wood into the front section where the stock stands upright. However, given that I got plenty of free off-cuts from my friends timber flooring business, I decided to put them in the front as well.

Once I get the mesh tacked in, all it needs is a lick of paint.
Hunting American dentists since 2015.
Reply
Thanks given by:
#84
Is the mesh going to run vertically to make sort of a cubby-hole?

Ed
Reply
Thanks given by:
#85
In my head it is going to be bent into a U shape and extend down from two of the low shelf supports.  This way if you have a length of stock that is shorter than the height of the second shelf, it will stand up in the rack and not fall over backwards or sideways.  

Quick and dirty Photoshop "artist's impression"


.jpg   forEd2.jpg (Size: 147.14 KB / Downloads: 129)
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
#86
This is from one of Ken's posts (post # 8) Access to the shelves is interesting as the rack fills. Because the heavier stuff tends to be shorter, as you get to the upper shelves they're still fairly open. The bottom (which isn't actually a shelf) has to be accessed from the side because the lowest part of the rack is so "densely populated."

Got me thinking. So if mine isn't against the wall I should have access to the shelves from the rear Thumbsup  (Provided it doesn't fall on me). Further thinking I arrived at this. A double sided stock rack Smiley-dancenana
     


Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#87
Till you fill up the front and back and still have to get to the smaller ones thru the side.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#88
(05-03-2015, 01:21 PM)Vinny Wrote: Till you fill up the front and back and still have to get to the smaller ones thru the side.

I thought about that as well ............... no answer as yet Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#89
You can always make it three sided, then you won't have to worry about getting access to an open end.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#90
(05-03-2015, 02:48 PM)Vinny Wrote: You can always make it three sided, then you won't have to worry about getting access to an open end.

Fabrication could be a bit tricky.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)