03-15-2015, 07:17 PM
|
Dumpster Dive Results
|
 
03-15-2015, 08:21 PM
(03-15-2015, 06:57 PM)mike-sid Wrote: They are gloss black. Must be my flash. I've seen several new car motor parts in the dumpster . I asked once and was told, not needed or wrong parts ordered so after a while they toss em. the seat cover may of faked out the camera
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
03-15-2015, 10:05 PM
any ideas what these can be used for?
How about listing them on Craig's List?
03-16-2015, 03:01 PM
Hi Lads
 A wee bit of recycling today at work , I had to make safe and scrap off a customers machine today , always fun to do and you you just dont no what you may fined . Well I ended up with this lot . ![[Image: P1080687_zpssu0ybqj6.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/P1080687_zpssu0ybqj6.jpg.html) ![[Image: P1080689_zpsynwbe8je.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/P1080689_zpsynwbe8je.jpg.html) Not bad when its cut into handy lengths , it was being used as ballast . I will turn it into tool holders and other work holding devices like these . ![[Image: P1040375.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Angle%20Plates/P1040375.jpg.html) ![[Image: P1040320.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Angle%20Plates/P1040320.jpg.html) Fabricated from steel plate Rob 
03-16-2015, 03:42 PM
Nice haul Rob!
Do you have a surface grinder or is that your shiny metal camera at work again. Oh, and I almost forgot.  Ed 
03-16-2015, 04:55 PM
That deserves a tremendous you suck Rob. What a find.
Free advice is worth exactly what you payed for it.
Greg 
03-16-2015, 05:07 PM
The luck some people have.................It meks me badly!
Nice haul Rob, but you made the Keats and the angle plate, surely? Phil ![[Image: you%20suck.gif]](http://www.metalworkingfun.com/images/smilies/you%20suck.gif)
Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
03-17-2015, 01:28 PM
Hi Lads ,
Yes I did make the angle and Keats style plates , welded construction  Rob 
03-17-2015, 02:01 PM
I love the look of that angle plate! The only thing I would have done differently would be to leave that top edge square on both sides because I might need to have a clamp right up near the top and would need that square to have a firm clamping area. Yours appears to have a big chamfer on the back side. Is that another optical delusion of mine?
03-17-2015, 03:37 PM
(03-17-2015, 02:01 PM)PixMan Wrote: I love the look of that angle plate! The only thing I would have done differently would be to leave that top edge square on both sides because I might need to have a clamp right up near the top and would need that square to have a firm clamping area. Yours appears to have a big chamfer on the back side. Is that another optical delusion of mine? Yer valid point , But as this angle plate is designed for face plate work ( reason for large rad on short leg ) I would not be using clamps to secure the work ,so no problem there ![[Image: Angle%20plates_zpsk1dqppwq.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Angle%20Plates/Angle%20plates_zpsk1dqppwq.jpg.html) Rob |
|
« Next Oldest | Next Newest »
|
Users browsing this thread: 5 Guest(s)