MetalworkingFun Forum › Machining › General Metalworking Discussion v
Dumpster Dive Results

Thread Modes
Dumpster Dive Results
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#81
02-08-2015, 05:58 PM
(01-15-2015, 06:17 PM)EdK Wrote: Hit the mother-load today. Two 3/4" aluminum (aluminium) plates, 18"x15".

Ed

Some have all the luck.  BTW You Suck
Reply
Thanks given by: EdK
Vinny Online
Another Whipping Boy
*******
Posts: 2,618
Threads: 100
Joined: Dec 2014
Location: Michigan
#82
02-09-2015, 03:21 PM
Since it's already got the stepper, looks like a good start for a micro-controller based dividing head.
Website
Reply
Thanks given by:
Hopefuldave Offline
Sophmore
***
Posts: 168
Threads: 6
Joined: Mar 2012
Location: Surrey, England
#83
02-09-2015, 05:03 PM
Yep, but I've already got a 6" rotary table and a tilting 4" with shared dividing plates...
The 4" Needs Attention though, the pivot pin's way off parallel to both the base and the table surface - another skip dive, I'm planning to bore the two castings between centres on the cross-slide boring table up on parallels, then bush to fit the pin back in - possibly adding another cylinder at a sensible centre distance for gauge blocks, sine table-ish? When I get the tuits I'll start a thread :-)
Rules are for the obedience of fools, and the guidance of wise men...
(Douglas Bader)
Reply
Thanks given by:
mike-sid Offline
Sophmore
***
Posts: 137
Threads: 16
Joined: Jan 2015
Location: Oxford, CT
#84
03-15-2015, 10:43 AM (This post was last modified: 03-15-2015, 10:48 AM by mike-sid.)
[Image: 20150315_102450_zpswevwapbn.jpg]

Found this matched set in my favorite dumpster. New never been mounted no scratches. Corporate America's answer to unwanted parts is to throw them out. Since I don't have the car to fit these, any ideas what these can be used for?
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
#85
03-15-2015, 11:56 AM (This post was last modified: 03-15-2015, 11:58 AM by Roadracer_Al.)
Google the part numbers and the manufacturer name, and you should be able to find a page that describes what they fit. Next stop, eBay.

This is one downside to being self employed which I had not considered before.... no dumpsters filled using other peoples money.
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
The following 1 user Likes PixMan's post:
mike-sid (03-15-2015)
#86
03-15-2015, 03:37 PM
Monroe Sensa Track p/n 72257 & 72258, left and right for Ford Focus 2006-2011
Reply
Thanks given by:
mike-sid Offline
Sophmore
***
Posts: 137
Threads: 16
Joined: Jan 2015
Location: Oxford, CT
#87
03-15-2015, 06:07 PM
(03-15-2015, 03:37 PM)PixMan Wrote: Monroe Sensa Track p/n 72257 & 72258, left and right for Ford Focus 2006-2011


Thanks!  
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#88
03-15-2015, 06:49 PM
I should have added that they are for the front. One thing I'm wondering about is why aren't they painted black as they should be? Makes me wonder if they were tossed because they skipped the paint or something else wrong with them.
Reply
Thanks given by:
mike-sid Offline
Sophmore
***
Posts: 137
Threads: 16
Joined: Jan 2015
Location: Oxford, CT
#89
03-15-2015, 06:57 PM (This post was last modified: 03-15-2015, 07:16 PM by mike-sid.)
They are gloss black. Must be my flash. I've seen several new car motor parts in the dumpster . I asked once and was told, not needed or wrong parts ordered so after a while they toss em.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 3 users Like Mayhem's post:
PixMan (03-15-2015), EdK (03-15-2015), Highpower (03-15-2015)
#90
03-15-2015, 07:16 PM
Any Vauxhall/Opel Z19TD engine parts in there by any chance...
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)