MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#3,861
02-12-2016, 06:29 AM
Graemlin

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#3,862
02-12-2016, 12:43 PM
I just hope it cures my stick-slip issue. Smiley-signs003

I know it will run more quietly now anyway. The upper bearing looked OK but the lower bearing did have moderate spalling / flaking of the inner and outer races. But since stuff flows downhill, that was to be expected even though they were both open bearings.
Willie
Reply
Thanks given by:
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#3,863
02-12-2016, 04:17 PM
It looks like the factory ran a form cutter at a fast clip. Those ridges in the root were on the sides at one time. Oil pockets. Smile
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 8 users Like Mayhem's post:
Pete O (02-14-2016), arvidj (02-14-2016), Highpower (02-14-2016), f350ca (02-14-2016), EdK (02-14-2016), rleete (02-14-2016), PixMan (02-15-2016), aRM (04-02-2016)
#3,864
02-14-2016, 04:47 AM
The bonus of fixing my friend's bump knurler was that I used it to make some brass screws for my vise stop on my mill.

   
   
Hunting American dentists since 2015.
Reply
Thanks given by: aRM
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
The following 2 users Like Highpower's post:
EdK (02-14-2016), arvidj (02-14-2016)
#3,865
02-14-2016, 09:47 AM
Hey Rob! Either Darren is stealing pictures of your work, or he stole your camera.... Chin

Big Grin
Willie
Reply
Thanks given by:
RobWilson
Unregistered
 
The following 3 users Like RobWilson's post:
EdK (02-14-2016), Highpower (02-14-2016), arvidj (02-14-2016)
#3,866
02-14-2016, 10:08 AM
(02-14-2016, 09:47 AM)Highpower Wrote: Hey Rob! Either Darren is stealing pictures of your work, or he stole your camera....   Chin

Big Grin


Narh !   he is just doing a mighty fine job  Big Grin  


Rob
Reply
Thanks given by: Mayhem
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#3,867
02-14-2016, 06:29 PM
(02-14-2016, 09:47 AM)Highpower Wrote: Hey Rob! Either Darren is stealing pictures of your work, or he stole your camera.... Chin

Big Grin

Thanks for the compliment Willie Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#3,868
02-14-2016, 07:27 PM
You earned it.... Graemlin
Willie
Reply
Thanks given by: Mayhem
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#3,869
02-15-2016, 08:56 PM
(02-14-2016, 07:27 PM)Highpower Wrote: You earned it....   Graemlin

Sure did! For a guy with no training in knurling those look perfect!
Reply
Thanks given by: Mayhem
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
DaveH (02-21-2016)
#3,870
02-21-2016, 10:53 AM
Not todays project but one that got lots of browny points.

https://www.youtube.com/watch?v=7dNH_QjFM0w
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)