MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
RobWilson
Unregistered
 
The following 5 users Like RobWilson's post:
arvidj (10-24-2015), EdK (10-24-2015), DanH (10-25-2015), Mayhem (10-25-2015), aRM (10-25-2015)
#3,511
10-24-2015, 12:35 PM
Knocked up a cable tie holder from a few bits of scrap 50mm x 50mm  box . 


[Image: P1100454_zpsf2k3ekaa.jpg]


Rob
Reply
Thanks given by: aRM
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#3,512
10-24-2015, 01:20 PM
good job rob
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
arvidj Offline
Junior
****
Posts: 742
Threads: 35
Joined: Feb 2012
Location: Minneapolis, MN
#3,513
10-24-2015, 01:25 PM
(10-24-2015, 12:35 PM)RobWilson. Wrote: Knocked up a cable tie holder from a few bits of scrap 50mm x 50mm  box . 

Rob

Smiley-signs107

I thought I was doing well to have them sorted into individual ZipLoc bags, all the bags in one box and knew where the box was most of the time.

Arvid
Reply
Thanks given by:
Kennyv Offline
Junior
****
Posts: 258
Threads: 30
Joined: May 2015
Location: NJ
The following 1 user Likes Kennyv's post:
Mayhem (10-25-2015)
#3,514
10-24-2015, 11:12 PM
Finally was able to do some work in the garage today. Started working on my parts for a work stop for the mill. Got most ops done  ran out of gas... To finish up all I gota do is cut slots  in all clamp block  sliders. . Cut the hardware to proper lengths. Put a finish on the parts, than modify  mill vice vice to accommodate the set up.   Was tired of using a make shift work stop figured this was 2nd worth spending the time on the new mill.


Attached Files Thumbnail(s)
           
Reply
Thanks given by:
Vinny Offline
Another Whipping Boy
*******
Posts: 2,629
Threads: 101
Joined: Dec 2014
Location: Michigan
#3,515
10-25-2015, 02:06 PM
Lookin good Kenny!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
Vinny Offline
Another Whipping Boy
*******
Posts: 2,629
Threads: 101
Joined: Dec 2014
Location: Michigan
#3,516
10-25-2015, 09:48 PM
FINALLY wired up the welder outlet yesterday. No pics, you seen one outlet hanging off the side of a breaker panel, you've seen them all.

Tonite I started up another long needed project out of that 1/2" square tubing I picked up a few months ago. Pic shows the pieces cut up, we'll see if anyone can figure out what it's going to be when it grows up. If it's not raining tomorrow I'll get it finished.

[Image: stock.jpg]

Any guesses?
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,501
Threads: 187
Joined: Feb 2012
Location: Missouri, USA
#3,517
10-26-2015, 05:41 AM
(10-25-2015, 09:48 PM)Vinny Wrote: [Image: stock.jpg]

Any guesses?

Chin

Chronograph sky screen bracket?   17428

That's what I made mine from anyway...   Rotfl
Willie
Reply
Thanks given by:
awemawson Offline
Junior
****
Posts: 642
Threads: 14
Joined: Oct 2013
Location: East Sussex, UK
#3,518
10-26-2015, 06:48 AM
My money's on a Welding Cart
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 5 users Like Mayhem's post:
f350ca (10-26-2015), EdK (10-26-2015), Highpower (10-26-2015), PixMan (10-26-2015), arvidj (10-26-2015)
#3,519
10-26-2015, 07:37 AM
My belated birthday present to me, from me  Drinks

   
   
   

Have the cable run to the board and I'll finish the wire up tomorrow, single phase 15A dedicated circuit with a combination MCB/RCD for protection.

The lights are going to get lifted and I will probably end up swapping them over to a lower profile.  My back is really going to love not having to crawl around under cars Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,896
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#3,520
10-26-2015, 08:51 AM
Wow, that looks like a tight fit, height wise. Sweat

Ed
Reply
Thanks given by:




Users browsing this thread: 16 Guest(s)