MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
arvidj Offline
Junior
****
Posts: 735
Threads: 34
Joined: Feb 2012
Location: Minneapolis, MN
#5,381
06-04-2023, 09:26 PM
What make and model cases?
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#5,382
06-05-2023, 12:16 AM
(06-04-2023, 09:26 PM)arvidj Wrote: What make and model cases?

Plano brand, got from Amazon.

Plano Cases

Ed
Reply
Thanks given by: arvidj
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
The following 7 users Like rleete's post:
EdK (06-05-2023), arvidj (06-05-2023), f350ca (06-05-2023), Highpower (06-05-2023), Vinny (06-06-2023), JScott (06-07-2023), Hawkeye (06-10-2023)
#5,383
06-05-2023, 06:09 PM (This post was last modified: 06-05-2023, 06:11 PM by rleete.)
As I haven't been down in the shop for a while, I figured I'd start with something simple, and knock one off the list.  

A simple home-made dead blow hammer.  Faces are polypropylene and Delrin.  Handle is ash with Danish oil finish.  Fitting is a 3/4 pipe thread in brass.
Lead shot - #7, I think - is inside.  It has 3.7 oz., which is about all it would hold and still leave space to move.
Handle is JB welded and pinned into handle.  Faces are threaded in; made with a cheap die I bought on a whim.



   
Full of ideas, but slow to produce parts
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#5,384
06-05-2023, 06:16 PM
Very nice! A machinist hammer is on my long list of projects.

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
The following 7 users Like EdK's post:
Highpower (06-10-2023), rleete (06-10-2023), Vinny (06-10-2023), f350ca (06-10-2023), arvidj (06-10-2023), JScott (06-12-2023), Dr Stan (06-16-2023)
#5,385
06-10-2023, 01:27 PM
Bought a small DI for dialing in stock in a four jaw chuck. It only has a travel of .25" but should be fine for that. Made a holder for it to drop onto the QCTP.

Ed

   
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
The following 8 users Like rleete's post:
EdK (06-13-2023), arvidj (06-13-2023), Highpower (06-13-2023), f350ca (06-13-2023), Vinny (06-13-2023), Hawkeye (06-13-2023), JScott (06-14-2023), Dr Stan (06-16-2023)
#5,386
06-13-2023, 03:37 PM
I'm pretty proud of this one.  It's an air fitting for my coworker's air-ride seat in his RV.  German made seat, so of course it's metric.  Only place to get them wanted over 22 bucks to ship, so I said I'd attempt to make one.  Hit all the numbers, and it only took me about an hour all told.  For me, that is lightning fast.

   
Full of ideas, but slow to produce parts
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#5,387
06-13-2023, 03:41 PM
Graemlin

Is that brass?

Ed
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
#5,388
06-13-2023, 03:44 PM
Yes. 1/4" bar, which is why the flange isn't quite as large as the original.
Full of ideas, but slow to produce parts
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
#5,389
06-13-2023, 05:17 PM
(06-13-2023, 03:44 PM)rleete Wrote: Yes.  1/4" bar, which is why the flange isn't quite as large as the original.

What do you use to make those grooves? I need a grooving tool. Chin

Ed
Reply
Thanks given by:
rleete Offline
Senior
*****
Posts: 768
Threads: 47
Joined: Mar 2012
Location: Rochester, NY
The following 3 users Like rleete's post:
Highpower (06-13-2023), Vinny (06-13-2023), JScott (06-14-2023)
#5,390
06-13-2023, 05:46 PM
Regular parting tool for the groves. I just walked it back and forth a little. I used a hand file for the tapered ends.
Full of ideas, but slow to produce parts
Reply
Thanks given by: EdK




Users browsing this thread: 140 Guest(s)