Todays Project - What did you do today?
David - excellent work on that watch.


(06-18-2013, 09:41 PM)f350ca Wrote: ...I was trying to figure out how to pull a mower spindle to remove a whole roll of 20 or 30 pound monofilament fishing line I picked up in the first 3 or 4 minutes mowing...

Is your grass that tall that you couldn't see the fisherman or didn't know you were driving into a lake?
Hunting American dentists since 2015.
Reply
Thanks given by:
(06-19-2013, 05:28 AM)EdK Wrote:
(06-18-2013, 08:23 PM)Highpower Wrote: Judging from the YT3500 decal I'd guess it's one of the models listed here in the YT 3000 series. Chin

Yup, I already found that link but other than to list model numbers there's not much information there.

Thanks though.

Ed

Click on the model numbers. They are links to the specs / info.....
I would take that info with a grain of salt though. It looks like they are all listed with single cylinder engines. Chin
Willie
Reply
Thanks given by:
(06-19-2013, 06:21 AM)Mayhem Wrote: David - excellent work on that watch.


(06-18-2013, 09:41 PM)f350ca Wrote: ...I was trying to figure out how to pull a mower spindle to remove a whole roll of 20 or 30 pound monofilament fishing line I picked up in the first 3 or 4 minutes mowing...

Is your grass that tall that you couldn't see the fisherman or didn't know you were driving into a lake?

Sign0142
Willie
Reply
Thanks given by:
Thanks guys I still have some work to do on it, the winding part of the watch is worn pretty bad which makes it hard to wind so I need to replace some of the parts and a couple jewel bearings on the balance wheel then it should be ready for another hundred years of service.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Got'r done!

Ed

   
Reply
Thanks given by:
The grass was so high I didn't even see the boat let alone the guy fishing.
Ed the catalogue shows it as 717-860-365 hope that helps. Had a little closer look and it is a CVT or belt drive transmission, but they did away with the usual forward reverse shifter and have it all on the pedal, works well for now anyway.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
another batch of shingles, cut these from 10 big blocks that I cut from logs at the dump, got to love scrounged.
[Image: IMG_0648.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
You find Cedar at the dump?
I don't think we even have dumps here. We have recycling centres where you pay to dump stuff and are not allowed to get stuff.
I'm thinking if it were a true recycling centre you'd be able to take stuff as well as bring it.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
I consider the dump as the local shopping mall. They have an electronics section, tire store, metal and hardware area and the cedar came from the organic section. But the best part is there return policy, no time limits and no recites required for a full refund.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
They have a "No Shopping" rule at our landfill.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:




Users browsing this thread: 10 Guest(s)