MetalworkingFun Forum › Machinery › Milling Machines v
Setting Up My PM935 Mill

Thread Modes
Setting Up My PM935 Mill
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 2 users Like EdK's post:
Highpower (12-13-2015), arvidj (12-13-2015)
#261
12-12-2015, 10:51 PM
I'm sure I'm overdoing this but rather that than under-doing it.  Smile

Ed
Reply
Thanks given by:
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
The following 1 user Likes Sunset Machine's post:
Highpower (12-13-2015)
#262
12-13-2015, 10:16 AM
I like handtrucks. Have 3 of them, just in case I lose one.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 2 users Like EdK's post:
PixMan (12-14-2015), wrustle (12-18-2015)
#263
12-13-2015, 03:40 PM
Other than another ratchet strap on the other side of the lifting ring, the ram is ready to slide down the basement. I got the pallet ready for the head but ran out of steam and had other obligations to take care of. Slow progress but at least it's progress.

Ed

         
Reply
Thanks given by:
wrustle Offline
Junior
****
Posts: 438
Threads: 67
Joined: Sep 2012
Location: Central Mass.
#264
12-19-2015, 05:54 PM
Looking good ED!!
Best Regards,
Russ

Check us out on Facebook and give us a "Like" 

Crosby Machine Company, Inc

Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#265
12-20-2015, 05:19 PM
I knew I wouldn't get much done this weekend since I was at a Christmas party at my sister's place all day yesterday. I did get the head mounted on its sled today though.

Ed

   
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
EdK (12-21-2015)
#266
12-20-2015, 09:14 PM
needs more rope and some lights before you take it out for a spin behind the snowmobile Big Grin Big Grin Big Grin
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#267
12-27-2015, 04:52 PM
I got the table all ready to remove from the mill and decided this would be a good use for the load leveler that came with the cherry picker. I get it hooked up to the cherry picker and notice one of the chain legs is shorter than the other.  17428

It must have been made on a Monday. I called it a day.  Bash

Ed

         
Reply
Thanks given by:
Vinny Online
Another Whipping Boy
*******
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
The following 2 users Like Vinny's post:
EdK (12-27-2015), Highpower (12-27-2015)
#268
12-27-2015, 06:17 PM
Looks like the second pic explains why one leg is shorter.... Prolly a good time to call it a day.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#269
12-27-2015, 06:51 PM
Ya think? Rotfl Rotfl Rotfl
Willie
Reply
Thanks given by:
arvidj Offline
Junior
****
Posts: 736
Threads: 34
Joined: Feb 2012
Location: Minneapolis, MN
The following 3 users Like arvidj's post:
EdK (12-28-2015), Vinny (12-28-2015), Highpower (12-28-2015)
#270
12-28-2015, 09:23 AM
The second picture is a feature that is not listed in the instructions that come with the leveler. It is the "blood pressure increaser". After you have everything hooked up and have the lift several feet off the ground the link will pop into it's correct position increasing the operators blood pressure by 40 points. You were not charged extra for this feature!!
Reply
Thanks given by:




Users browsing this thread: 40 Guest(s)