Stock racks...what do you use?
#41
It may be beneficial if Ken could tell us how his rack was made.
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#42
Darren, any idea how much angle iron it takes - rough guess Smile 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#43
Roughly 67 feet Dave, assuming I didn't make any addition errors. Blush

Ed
Reply
Thanks given by:
#44
Thanks Ed,
I have some 40 x 3 angle iron not enough for the whole rack though. I have some 32 x 3 angle and a whole lot of 25 and 32 square tube. Trying to see what I have can be used without it looking a total mess.
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#45
If it comes out a total mess, call it art.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#46
(04-29-2015, 05:21 PM)Vinny Wrote: If it comes out a total mess, call it art.

......... and sell it Rotfl
I'm still trying to figure how to make it and with what. 17428
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#47
Bed rails from the dump.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#48
I'm a long length of 40 x 3 angle short, so I was trying to use what I have. For the two sloping angle irons I thought I could use 32 square tube, fixing it flat on, but it ends up skew because of the thickness of the angle rear frame. Altering the design a touch will get rid of the skew but then the angles that hold the shelves (the 6 outer ones) are skew.  Bash 
I could 'notch' the tubing - not the best thing to do.
So I'm still in the 'thinking mode' and it is not going well Big Grin 
Also I can't quite see where the top angle iron goes 17428 is it fixed to the rear angle iron or to the sloping angles?

But apart from that it's going like a Boeing  Smile 
  Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#49
(04-28-2015, 06:53 PM)DaveH Wrote: It may be beneficial if Ken could tell us how his rack was made.
Smiley-eatdrink004 
DaveH

LOL....made by Union labor here in Massachusetts with American made steel.

No idea really, it's a commercially made Hodge Manufacturing Co, formerly of Springfield MA.
Reply
Thanks given by:
#50
(04-29-2015, 07:33 PM)PixMan Wrote:
(04-28-2015, 06:53 PM)DaveH Wrote: It may be beneficial if Ken could tell us how his rack was made.
Smiley-eatdrink004 
DaveH

LOL....made by Union labor here in Massachusetts with American made steel.

No idea really, it's a commercially made Hodge Manufacturing Co, formerly of Springfield MA.
Ken,
Rotfl  I didn't mean that, I meant which bit is welded to which bit. eg the top angle iron I can't see exactly where that is welded. Also the sloping angle is it cut at the top to fit, or is the rear upright angles cut so the sloping angle fits?

I think it is so well designed to use only one eighth thick angle iron. If one looks at it closely it is nearly impossible to find a fault with it and whoever designed it did it really well.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)