MetalworkingFun Forum › Machinery › Lathes v
Lathe Cross Slide Problem

Thread Modes
Lathe Cross Slide Problem
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#121
06-25-2014, 04:39 PM
(06-25-2014, 02:56 PM)stevec Wrote: Ed, I dunno if I'm on track here or not but the following thought comes to mind.
With every thing assembled, the cross slide close to the operator (you) and the nut under the hole in the cross slide make a mark on the nut then slide the cross slide as far away from you and wind the nut under it and see if your reference mark lines up.
Chin

Hmmm, that just might do the trick Steve. Then if I screw up I can blame you. I like it! Big Grin

Ed
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
The following 1 user Likes stevec's post:
EdK (06-25-2014)
#122
06-25-2014, 05:20 PM
Wait! maybe I'm wrong! ( oh no not again Slaphead)
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#123
06-25-2014, 05:26 PM
(06-25-2014, 05:20 PM)stevec Wrote: Wait! maybe I'm wrong! ( oh no not again Slaphead)

Rotfl Rotfl
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
The following 4 users Like EdK's post:
stevec (06-27-2014), kenne (06-27-2014), PixMan (06-27-2014), arvidj (06-27-2014)
#124
06-27-2014, 02:46 PM
Finally got around to drilling the hole for the roll pin that holds the gear in place.

Ed

       
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#125
06-27-2014, 06:31 PM
Oops! Not good. Blush

Ed
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#126
06-27-2014, 08:21 PM
(06-27-2014, 06:31 PM)EdK Wrote: Oops! Not good. Blush

Ed

Uh oh...what's wrong?
Reply
Thanks given by:
kenne Offline
Sophmore
***
Posts: 97
Threads: 5
Joined: Jun 2014
Location: las vegas burbs
#127
06-28-2014, 01:28 AM
Yikesat least we will know who's fault it is , Hope it's not to serious
kenne, proud to be a member of MetalworkingFun Forum since Jun 2014.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#128
06-29-2014, 10:38 AM
Sorry for the late response. I was at a family picnic all day yesterday.

I tried fitting the nut to the lead screw and it's too tall to clear the trough in the saddle. See sketch below. The green is the nut and the blue dashed line is the trough. I need to do some more measurements to see if this is salvageable. Sweat

Ed

   
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#129
06-29-2014, 06:45 PM
Before modifying it, be sure it's not something where it could fit as is if lifted over and into a well inside the assembly. Or, can you easily modify the place where it should land?
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,889
Threads: 320
Joined: Feb 2012
Location: Arizona/Minnesota
#130
06-29-2014, 07:53 PM
(06-29-2014, 06:45 PM)PixMan Wrote: Before modifying it, be sure it's not something where it could fit as is if lifted over and into a well inside the assembly. Or, can you easily modify the place where it should land?

Ken,

Yup, both of those things are what I need to look into. I didn't get time today but I've got all this week off so I'm going to dig into it tomorrow.

Ed
Reply
Thanks given by:




Users browsing this thread: 14 Guest(s)