Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 3 users Like Mayhem's post:
EdK (04-26-2015), PixMan (04-26-2015), arvidj (04-26-2015)
It is funny that you should say that Ken, as the very first piece I grabbed was just an inch too short to stand up. I'm thinking about placing a piece of weld mesh in that space on one of the three sections.
I tend to make my shelves out of angle that way, as then I can simply cut some wood to size and drop it in.
I don't own a brake of any size but I would like to have one. However, for the amount of work it would get, I cannot justify finding the space to keep it. Although, having said that, if I had one it may get a lot of use...
One thing I forgot to mention is that I wasn't sure how long each divider poked out from the shelves, as it wasn't on the drawing. The solution was simple. I took a length of angle and set the bottom flush with front of the base of the rack. I then tilted it back until it was parallel with the angled side of the rack and clamped it in place. I then measured from the rear of the shelf to the guide, marked and cut. The finishing touch, which isn't evident in the picture is the 1/2" radius ground onto the corners of the dividers.
Hunting American dentists since 2015.
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
The following 1 user Likes PixMan's post:
Mayhem (04-26-2015)
What a great idea to put a mesh in that area! Come over and upgrade mine!
Sorry about omitting those dimensions. Strange, because I recall measuring them. Oops.
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
(04-26-2015, 12:01 PM)PixMan Wrote: What a great idea to put a mesh in that area! Come over and upgrade mine!
Can you wait until October?
(04-26-2015, 12:01 PM)PixMan Wrote: Sorry about omitting those dimensions. Strange, because I recall measuring them. Oops.
No worries, it wasn't a problem to figure it out. For me the key dimensions were the actual frame itself, as it was the size that I liked. The configuration of the shelves and whether I made it 3 bays or 4 doesn't matter.
Hunting American dentists since 2015.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Are these racks able to stand without any support (ie against a wall) can I use one in the middle of the work shop?
DaveH
Posts: 8,854
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
Darren,
When you get a chance, would you please post some close-up pictures of your rack? Especially the joints. I'm drawing this up and am not sure how the joints are done.
Thanks,
Ed
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
Dave - yes, it is free standing,as can be seen in my picture. You can always bolt it to the floor if you are concerned.
Ed - when I'm in the shop next I'll get some pictures. Most joints are notched.
Hunting American dentists since 2015.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Thanks Darren,
Initially I thought it would need to stand against a wall, then I saw the pic of yours made me re-think it.
DaveH
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
Ed - here is a picture from Google showing a notched angle ready for welding:
https://s-media-cache-ak0.pinimg.com/236...7a4cc0.jpg
I think these are also referred to as copes.
Hunting American dentists since 2015.
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
(04-27-2015, 05:48 PM)Mayhem Wrote: Dave - yes, it is free standing,as can be seen in my picture. You can always bolt it to the floor if you are concerned.
Ed - when I'm in the shop next I'll get some pictures. Most joints are notched.
I don't think it would be safe to leave it free-standing away from a wall without lagging it to the floor....IF there's a lot of longer stock leaning on the angled side without compensating "ballast" of full, heavy shelves.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
(04-27-2015, 09:39 PM)PixMan Wrote: I don't think it would be safe to leave it free-standing away from a wall without lagging it to the floor....IF there's a lot of longer stock leaning on the angled side without compensating "ballast" of full, heavy shelves.
I can use some (4) rawl bolts and fix it to the concrete floor. I thought about extending the angle iron to make a larger base (good for tripping over
) I could make it double sided but I would still have to be careful balancing each side.
I have a lot of metal 3meters long (10 foot) - not round bar, mainly square/round tubing, angle iron, flat bar all different sizes it would be nice to get it off the floor? I don't like cutting if smaller - tends to be wasteful, especially if I want a couple pieces of angle 2100mm long and I have cut it 1500mm long
DaveH
