Lights For The Mill
#1
I bought these two lights for $4 with a $4 rebate at the local home center. The bodies are made of aluminum and they are reasonably bright using LEDs rather than a light bulb. Some time ago I bought a few goose-necks that are normally used for microphones with the intent on using them to hold some lights for the mill. That time has arrived. These should work real slick for shining light on the workpiece as I'm milling it. The lights are only about 4" long and 7/8" in diameter and are powered by three AA batteries. I'll wire a power supply into them so I don't have to deal with the batteries. Not bad for almost 0$.

Ed

   
Reply
Thanks given by:
#2
Ed
If there is an Ikea close these little lights are great. The flex part is threaded onto the base, I made little brackets and have them on the lathe and mill.
http://www.ikea.com/ca/en/catalog/products/20169658/
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#3
(09-07-2012, 04:34 PM)f350ca Wrote: Ed
If there is an Ikea close these little lights are great. The flex part is threaded onto the base, I made little brackets and have them on the lathe and mill.
http://www.ikea.com/ca/en/catalog/products/20169658/

Greg,

That's a real nice option and would save me some work. I think I'll get one of those for the lathe. Thanks for posting the link. Thumbsup

Ed
Reply
Thanks given by:
#4
I purchased this one at BusyBee Tools in Ottawa last week. It works nice but I think the one from Ikea might be better.
http://www.busybeetools.com/products/LED...-BASE.html
claudef, proud to be a member of Metalworking Forum since Mar 2012.
Reply
Thanks given by:
#5
I stole an idea from our friend Jerry after seeing a picture of his machine with some trac-lights mounted on the wall behind it. I bought a set of the small halogen lights and a long section of track, and mounted it overhead if front of my mill. You can move the lights anywhere on the track and tilt & pivot them to point exactly where you need the light.

And since they are overhead and not down near the table, I don't have to worry about smacking into that goose neck that always seems to end up in the way. Plus, they keep me nice and warm in the winter. Rotfl
Willie
Reply
Thanks given by:
#6
I got one of these at Rockler. The mag base is very nice!

http://www.rockler.com/product.cfm?page=...te=ROCKLER
Reply
Thanks given by:
#7
(09-07-2012, 09:42 PM)Highpower Wrote: I stole an idea from our friend Jerry after seeing a picture of his machine with some trac-lights mounted on the wall behind it. I bought a set of the small halogen lights and a long section of track, and mounted it overhead if front of my mill. You can move the lights anywhere on the track and tilt & pivot them to point exactly where you need the light.

And since they are overhead and not down near the table, I don't have to worry about smacking into that goose neck that always seems to end up in the way. Plus, they keep me nice and warm in the winter. Rotfl
Hay Willie show me your setup, I've been considering improving mine.Drool
Jerry.Popcorn
ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#8
Nothing to it Jerry! Take your lights off the back wall, and then attach them to the ceiling over your head where you stand at the machine. Smile
Willie
Reply
Thanks given by:
#9
Those Ikea lights are neat, thanks for the link. I can use those in lots of places, good price too.
Ken
An old tired/retired/wanna-be machinist. Cool
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)