Todays Project - What did you do today?
Looking good Steve. Expecting an early winter? You really shouldn't be doing something like that before your freezing your fingers.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
(09-06-2012, 04:54 PM)stevec Wrote: Today I finally finished the "front" mounting of my snow blower to my old Allis-Chalmers CA tractor (circa 1953).

[Image: attachment.php?thumbnail=2853]

Nice CA and nice work on the driveshaft. I'd love to have a wide front end like that on my WD45 as it can get a little "tense" when I have my front loader on it.

-Ron
11" South Bend lathe - Wells-Index 860C mill - 16" Queen City Shaper
Reply
Thanks given by:
Thanks Jerry ThumbsupRotfl
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
(09-06-2012, 10:05 PM)f350ca Wrote: Looking good Steve. Expecting an early winter? You really shouldn't be doing something like that before your freezing your fingers.
Actually I'm about 10 months late due to my little mishap in the woods last Sept.Angry
Thanks for the comments guys. Smile
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(09-06-2012, 08:31 PM)Highpower Wrote: Is that a steering shaft/u-joint under there?
Willie, nah, it's a u-joint I bought at Princess Auto which is a guy place for us Canajuns who like to putter mechanicaly. They also furnished some of the sprockets and pillow blocks- great prices.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(09-07-2012, 01:56 AM)ScrapMetal Wrote: I'd love to have a wide front end like that on my WD45 as it can get a little "tense" when I have my front loader on it.

-Ron
Ron, do you visit the "Unofficial Allis Chalmers forum"?
http://www.allischalmers.com/forum/forum...-equipment

You might be able to find a wide front for your WD45 there.
Here's a pic of the loader I built for my "B"
   
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: ScrapMetal
I just realized I posted an older pic of the front blower that only shows the plough lift that came with the tractor when I got it 10 or 12 years ago.
Here's the front mounted blower.

   

I think the wires to the chute turner I cobbled out of a little 12 VDC winch are long enough, we'll see.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(09-07-2012, 06:45 AM)stevec Wrote:
(09-07-2012, 01:56 AM)ScrapMetal Wrote: I'd love to have a wide front end like that on my WD45 as it can get a little "tense" when I have my front loader on it.

-Ron
Ron, do you visit the "Unofficial Allis Chalmers forum"?
http://www.allischalmers.com/forum/forum...-equipment

You might be able to find a wide front for your WD45 there.
Here's a pic of the loader I built for my "B"

I wasn't even aware of that forum - not that I have time to devote to yet another forum. Tongue (six seems to be my limit). I will start doing a bit of lurking over there though. Blush Thanks much.

Great shot of the "B" btw.

-Ron
11" South Bend lathe - Wells-Index 860C mill - 16" Queen City Shaper
Reply
Thanks given by:
(09-07-2012, 06:54 PM)ScrapMetal Wrote: - not that I have time to devote to yet another forum.
-Ron
I know what you meanSmiley-signs064
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Hi,
Normally I can't remember what "I did today" - easy answer I'll write down what "I did today" Thumbsup

Now if I can just find the bit of paper I wrote it down on ............... Chin Smiley-dancenana
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 25 Guest(s)