Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
Could work aRM, check the voltage on the leads, should be able to adjust it with the current setting on the welder to say 12 v to start. Hook it up to the electrolyte bath with an amp meter in the circuit to see what its drawing.
Free advice is worth exactly what you payed for it.
Greg
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
(05-26-2015, 04:39 PM)f350ca Wrote: Could work aRM, check the voltage on the leads, should be able to adjust it with the current setting on the welder to say 12 v to start. Hook it up to the electrolyte bath with an amp meter in the circuit to see what its drawing.
'Tis worth a shot Greg
Will look at that with a bit more detail
Thanks
aRM
Posts: 168
Threads: 6
Joined: Mar 2012
Location: Surrey, England
The following 1 user Likes Hopefuldave's post:
f350ca (05-28-2015)
aRM, remember the electronic engineers' Rule of Toe when selecting a transformer - drop it on your foot, it'll give as many amps as the toes it breaks...
Rules are for the obedience of fools, and the guidance of wise men...
(Douglas Bader)
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
(05-27-2015, 01:12 PM)Hopefuldave Wrote: aRM, remember the electronic engineers' Rule of Toe when selecting a transformer - drop it on your foot, it'll give as many amps as the toes it breaks...
Hey Dave
This one will break all our toes, so we reckon it would do.
The lowest setting is 55 Amps and we don't have an Amp meter to test the reading - GREG
Duh question - but if it is overpowered, what are consequences and/or the possibilities of it like blowing up the works ???
The little we know, it will trip the house Main Circuit Board !!!
Do we go ahead ???
aRM
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
05-28-2015, 06:00 AM
(This post was last modified: 05-28-2015, 06:01 AM by stevec.)
aRM, I'd be surprised if the electrolysis process would draw 55 amps. But I don't know what the potential, higher than 12 +/- volts, would do to the process.
Steve
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
(05-28-2015, 06:00 AM)stevec Wrote: aRM, I'd be surprised if the electrolysis process would draw 55 amps. But I don't know what the potential, higher than 12 +/- volts, would do to the process.
Steve
That's exactly our dilemma !!!
aRM
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 3 users Like dallen's post:
PixMan (05-28-2015), EdK (05-28-2015), f350ca (05-28-2015)
while at the hardware store yesterday I spotted an 8" slim taper 3 cornered file that would work for sharpening my handsaw, and backsaw.
So today I got the supreme pleasure of sharpening the handsaw that used to be my Dad's, this saw is probably older then I am I know my dad got it from the sawmill that he used to work at back in the 50's. Thing cuts like it was brand new again. After sharpening it I sawed the end off of a 3X4 piece of dry oak timber in just a matter of a couple minutes.
Now I just need to find a saw set on Evil Bay that I can afford to buy.
DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
05-29-2015, 03:30 PM
(This post was last modified: 05-29-2015, 03:30 PM by Roadracer_Al.)
I believe I have at least 2 or 3. I'd have to look for them, though. I'd be happy to part with one.
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
(05-29-2015, 03:30 PM)Roadracer_Al Wrote: I believe I have at least 2 or 3. I'd have to look for them, though. I'd be happy to part with one.
if your talking about a saw set I'm looking for one if you have one that you would like to get rid of one.
DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
RobWilson
Unregistered
The following 4 users Like RobWilson's post:
arvidj (05-31-2015), EdK (05-31-2015), Mayhem (05-31-2015), PixMan (05-31-2015)
Hi Lads
Just finished knocking up a couple of ramps to use at work , 3 ft x 1 ft x 6" made from a wee bit of 1/8 plate .
Good for 50 ton the pair
Rob
|