Hello all, I haven't been around in...about half a decade...but I am doing something that definitely belongs here and I have plenty of questions that I know others here can probably help me with. That being said, let me tell you about the journey I would like to embark upon that I hope you would like to be a part of.
In 2012 while deployed to Afghanistan as an Explosive Ordnance Disposal (EOD) Technician I purchased my 1945 Craftsman lathe from a Vietnam Veteran that bought it from a WWII Veteran. Because of that history I am not willing to modify the lathe in any permanent way. It has been lovingly maintained and has made it 72 years in excellent condition so I am not going to do anything to it that will not be able to turned back.
Knowing that enormous caveat to this experiment, I must also say that I am completing the 7th quarter of a 9 quarter Precision Machining Technologies program and have access to a hone, heat treat equipment, a surface grinder and a full CNC shop as well as manual. As long as I can get the parts that will be needed designed and made in the next 7-8 months I should be able to complete this after that with OTC parts.
My aims for this lathe are to basically just automate what the lathe was capable of doing from the factory. I am not looking to turn this machine into something that it isn't, and there are a lot of things that this machine isn't. That said, I think that it is fair to shoot for light depth of cut and .010 IPR with the factory max spindle speed of 2000rpm.
So far I am planning on using a 12mm ball screw going through the factory ACME screw hole for the cross slide and making a bearing support that bolts where the taper attachment would bolt from the factory. This is also going to require making a threaded bearing carrier to replace the micrometer collar and ACME screw bearing support. That should take control of the X axis, although I will also need to make a new tool post mount that replaces the compound.
I am planning on using a 20mm ball screw located in the factory lead screw position. In order to do this I plan on removing the apron from the my lathe and making an attachment to connect the ball screw nut in place of the factory apron.
I am currently leaning toward a Leadshine closed loop hybrid system for motion and I have contacted Jooman on Amazon about ball screws. I think a NEMA 34 3Nm should work for the cross slide with a NEMA 34 4Nm for the Z axis. I pulled those numbers completely from my rear end though. At the moment I am focusing my efforts on stripping the ACME screw from the carriage. After that I will probably move to take the lead screw out so I can get the carriage off and take it all to school so that I can get the measurements for making the adapters. By then I hope to have the ball screws so that I can finalize the designs and get them rendered in SolidWorks, processed through MasterCAM (school's programs) and machined. Turning will probably be done on a Doosan Lynx 220 with milling done on a Doosan DNM 400. That could change as it gets closer as well. We have Haas machines and a Mazak at school as well.
Enough with all the words, here are some pictures because that is really what we are all here for!
In 2012 while deployed to Afghanistan as an Explosive Ordnance Disposal (EOD) Technician I purchased my 1945 Craftsman lathe from a Vietnam Veteran that bought it from a WWII Veteran. Because of that history I am not willing to modify the lathe in any permanent way. It has been lovingly maintained and has made it 72 years in excellent condition so I am not going to do anything to it that will not be able to turned back.
Knowing that enormous caveat to this experiment, I must also say that I am completing the 7th quarter of a 9 quarter Precision Machining Technologies program and have access to a hone, heat treat equipment, a surface grinder and a full CNC shop as well as manual. As long as I can get the parts that will be needed designed and made in the next 7-8 months I should be able to complete this after that with OTC parts.
My aims for this lathe are to basically just automate what the lathe was capable of doing from the factory. I am not looking to turn this machine into something that it isn't, and there are a lot of things that this machine isn't. That said, I think that it is fair to shoot for light depth of cut and .010 IPR with the factory max spindle speed of 2000rpm.
So far I am planning on using a 12mm ball screw going through the factory ACME screw hole for the cross slide and making a bearing support that bolts where the taper attachment would bolt from the factory. This is also going to require making a threaded bearing carrier to replace the micrometer collar and ACME screw bearing support. That should take control of the X axis, although I will also need to make a new tool post mount that replaces the compound.
I am planning on using a 20mm ball screw located in the factory lead screw position. In order to do this I plan on removing the apron from the my lathe and making an attachment to connect the ball screw nut in place of the factory apron.
I am currently leaning toward a Leadshine closed loop hybrid system for motion and I have contacted Jooman on Amazon about ball screws. I think a NEMA 34 3Nm should work for the cross slide with a NEMA 34 4Nm for the Z axis. I pulled those numbers completely from my rear end though. At the moment I am focusing my efforts on stripping the ACME screw from the carriage. After that I will probably move to take the lead screw out so I can get the carriage off and take it all to school so that I can get the measurements for making the adapters. By then I hope to have the ball screws so that I can finalize the designs and get them rendered in SolidWorks, processed through MasterCAM (school's programs) and machined. Turning will probably be done on a Doosan Lynx 220 with milling done on a Doosan DNM 400. That could change as it gets closer as well. We have Haas machines and a Mazak at school as well.
Enough with all the words, here are some pictures because that is really what we are all here for!
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
