MetalworkingFun Forum › Machining › General Metalworking Discussion v
Machining Chamfers

Thread Modes
Machining Chamfers
EdK Offline
Whipping Boy
*******
Posts: 8,742
Threads: 313
Joined: Feb 2012
Location: Arizona/Minnesota
#1
10-08-2016, 01:44 PM
This may sound like a dumb question but here goes. When a drawing calls out a chamfer dimension of say .25 x 45 degrees, is that .25" dimension the measurement of the face of the chamfer or some other dimension? 17428

Ed
Reply
Thanks given by:
RobWilson
Unregistered
 
The following 3 users Like RobWilson's post:
Mayhem (10-08-2016), DaveH (10-09-2016), arvidj (10-09-2016)
#2
10-08-2016, 01:53 PM
Hi Ed 


The .25 it the depth of the chamfer , the face dimension would be hard to accurately measure ,especial on say the end of a round bar . 

[Image: P1140261_zpsjf339hqn.jpg]


Rob
Reply
Thanks given by: Highpower , EdK
EdK Offline
Whipping Boy
*******
Posts: 8,742
Threads: 313
Joined: Feb 2012
Location: Arizona/Minnesota
#3
10-08-2016, 03:07 PM
Thanks Rob, that makes sense.

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 1 user Likes Mayhem's post:
arvidj (10-09-2016)
#4
10-08-2016, 05:11 PM
I see that BobCad is one step up on AmishCad, giving the ability to add colour to the print.
Hunting American dentists since 2015.
Reply
Thanks given by:
the penguin Offline
Junior
****
Posts: 482
Threads: 89
Joined: Oct 2012
Location: camillus (syracuse), ny
#5
10-08-2016, 05:58 PM
(10-08-2016, 05:11 PM)Mayhem Wrote: I see that BobCad is one step up on AmishCad, giving the ability to add colour to the print.

similar to AmishCad version 1.1.1.02 .....................
jack
Reply
Thanks given by:
wawoodman Offline
Junior
****
Posts: 340
Threads: 24
Joined: Aug 2014
Location: Seattle, WA
The following 2 users Like wawoodman's post:
EdK (10-08-2016), DaveH (10-09-2016)
#6
10-08-2016, 11:01 PM
Shouldn't that be RobCAD?
Mike

SB 10K (1976) Rockwell vertical mill (1967) Rockwell 17" drill press (1946) Me (1949)
Reply
Thanks given by:
RobWilson
Unregistered
 
#7
10-09-2016, 10:24 AM
(10-08-2016, 11:01 PM)wawoodman Wrote: Shouldn't that be RobCAD?

Hi Mike ,   I also get called Bob at work ,,,,,,,,,,,,,,,,,,,,,,,,,,, along with few other  names that begin with A,B and C  by the apprentice boys Slaphead



Rob Big Grin
Reply
Thanks given by:
RobWilson
Unregistered
 
The following 2 users Like RobWilson's post:
EdK (10-09-2016), Mayhem (10-09-2016)
#8
10-09-2016, 10:27 AM
(10-08-2016, 05:58 PM)the penguin Wrote:
(10-08-2016, 05:11 PM)Mayhem Wrote: I see that BobCad is one step up on AmishCad, giving the ability to add colour to the print.

similar to AmishCad version 1.1.1.02 .....................

Surly If it was AmishCad   it would be version 1', 1".5/8  Rotfl


Rob
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)