Behind the scenes........pics.
#11
(11-25-2015, 10:27 AM)EdK Wrote: Nice tip on the rubber bands.

Ed

Just be sure to always double them up Ed!

One hot chip, the band breaks, your parallel moves.........it's pulling them out, cleaning and starting again!

99% of the time we use parallel keepers, but for some setups, a good old rubber band is just the ticket!!
Best Regards,
Russ

Check us out on Facebook and give us a "Like" 

Crosby Machine Company, Inc

Reply
Thanks given by:
#12
(11-25-2015, 11:26 AM)wrustle Wrote: Just be sure to always double them up Ed!

One hot chip, the band breaks, your parallel moves.........it's pulling them out, cleaning and starting again!

99% of the time we use parallel keepers, but for some setups, a good old rubber band is just the ticket!!

Another good tip. Thumbsup

Ed
Reply
Thanks given by: wrustle
#13
Short lives I expect with those rubber bands if you're running coolant
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
#14
(11-25-2015, 11:34 AM)awemawson Wrote: Short lives I expect with those rubber bands if you're running coolant

The coolant we have is outstanding, and all those issues went away when we switched over to it.

Now it's mostly the chips that will get to them.

The previous coolant we had though would eat through them in very short order.

We keep a big box of them at the ready though!!
Best Regards,
Russ

Check us out on Facebook and give us a "Like" 

Crosby Machine Company, Inc

Reply
Thanks given by:
#15
Summer time at the shop in West Brookfield, Mass.


Being that it is Thanksgiving tomorrow...........it seems sooooooo far away right now!

[Image: IMG_0185_zpsxwtumwj8.jpg]

[Image: 20140824_092225_zpsnoxschu3.jpg]

[Image: 20140824_092256_zpsaw4a1rev.jpg]
Best Regards,
Russ

Check us out on Facebook and give us a "Like" 

Crosby Machine Company, Inc

Reply
Thanks given by:
#16
Our first measurable snow is supposed to arrive tomorrow so I'm not complaining. That's way later than average.

Ed
Reply
Thanks given by:
#17
He did say the pic was taken in the SUMMER Ed. :)
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
#18
(11-25-2015, 04:49 PM)Vinny Wrote: He did say the pic was taken in the SUMMER Ed.   :)

Smiley-signs125    Bash

I need to quit taking quick peeks at posts and actually read them more thoroughly.  Blush

Ed
Reply
Thanks given by:
#19
I appreciate you sharing that with us Russ!

This shows how much you are thinking the jobs through for maximum efficiency. I can't tell you how many times I've seen shops "spinning the wheels" by plowing through material at high "cubic inches per minute" material removal rates, only to stand there deburring parts or loading 64 pieces on a tombstone while the spindle is idle.

Maximizing productivity is all about balance, and that's what you are actively doing. It's going to keep your costs down for you and your customers, assuring repeat work. You are setting up Andrew and others for the future well, so you'll be able to just "consult" when you retire. Smile
Reply
Thanks given by:
#20
That's the problem I had working those shops - too focused on the immediate, not the whole job. I failed at production; I'd rather do repairs. Carbide tooling just gets set aside, I don't even own a single insert.
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)