few small projects

[Kennyv]

Gettin a little itchy waiting for my New Machines to arrive at the house PM-25MV -PM1022 still not sure what hobby is going to catch my fancy. Guys I need a home hobby bad bc at work I do not do any challenging work.


So In the mean time B/T work lunch/ break made a few small  projects to get my mind thinking again .  
Spring loaded centers .Than after hours    made  2 sliders  for my table saw at home .  One is a compound  with graduations the other is  a 90 degrees slider with a T slot  for a clamping fixture . . Fig it would become useful cutting alum stock. Didn't   have much stock so  used what I can scrape up.  Still need to make the Pointer.

 Right now only have little stuff on my to do list. Clamps Hold downs for precision machinist vice , boring bars, fly cutters, Dove tail cutters ect...  Ohh I do have some ideas (on a few napkins) for a  tool  indexer table  for a shop  built carbide bench grinder However  Dont have the motor yet .lol...  

well after that im  still at a loss what im gona do ... Anyone chime in  Love to hear some more  ideas of some useful tooling …

[dallen]

nice work on the sliders and spring centers, I really need to make one of those

[TomG]

Nice job and thanks for sharing.

Every time I tap something on the lathe I think about making a spring center, but then I move on to something else and forget.

Something I use all the time on the mill are stack blocks for propping up strap clamps and such. There are plans on my website.

Tom

[Vinny]

I saw you using them in a couple of your videos. Those things are slick and are on my todo list.

[EdK]

Vinny,

Escalate them to the top of the list. They are very handy.

http://www.metalworkingfun.com/showthread.php?tid=846

Ed

[Vinny]

After what I just went thru trying to find a washer the right thickness tonite, they've been escalated!

[PixMan]

A washer the right thickness....now there's a project I could/should latch onto.

One of these days I'll get a hole drilled through some 1" steel stock and part off a series of 1/8", 5/32", 3/16", 1/4" (and so on) thick washers/spacers in pairs. When using the Te-Co step block clamp sets it seems I'm always finding the stud to be just a little too long and I reach for the nail with a bunch of 1/16" thick washers. It would be better to grab ONE that's the right thickness.

[EdK]

(06-04-2015, 07:59 PM)PixMan Wrote: ...

One of these days I'll get a hole drilled through some 1" steel stock and part off a series of 1/8", 5/32", 3/16", 1/4" (and so on) thick washers/spacers in pairs. When using the Te-Co step block clamp sets it seems I'm always finding the stud to be just a little too long and I reach for the nail with a bunch of 1/16" thick washers. It would be better to grab ONE that's the right thickness.

Now that's another good idea. Especially since I no longer fear parting off under power thanks to you Ken.

Ed

[Roadracer_Al]

Ed, you must have transferred that fear of parting to me. I had a parting tool blade go BANG under power feed last week, and now I'm jumpy like a cat in a room fulla' rockin' chairs when I part off.

[EdK]

(06-05-2015, 04:28 PM)Roadracer_Al Wrote: Ed, you must have transferred that fear of parting to me.  I had a parting tool blade go BANG under power feed last week, and now I'm jumpy like a cat in a room fulla' rockin' chairs when I part off.

Well then transfer it to someone else so you can get over it.

Ed