MetalworkingFun Forum › Machinery › Milling Machines v
[PROJECT] X Power Feed

Thread Modes
Project X Power Feed
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#31
02-01-2015, 09:03 PM
(02-01-2015, 08:42 PM)dallen Wrote: you could turn those two around

Yup, I see that now. Too late, I'm done with that feature but I'll remember that next time, I think.
Thanks for the tip.

Ed
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#32
02-01-2015, 09:18 PM
(02-01-2015, 08:42 PM)dallen Wrote: you could turn those two around

That's what I do in such a case. Works fine.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#33
02-02-2015, 12:19 AM
You could eat off that lathe Ed! Nice work.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 4 users Like EdK's post:
Highpower (02-08-2015), Mayhem (02-08-2015), PixMan (02-08-2015), arvidj (02-08-2015)
#34
02-08-2015, 03:29 PM
It's coming along slow but sure.

Ed

         


   
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#35
02-08-2015, 03:35 PM
What type of lubrication should be used with this needle bearing? I'm assuming grease since re-lubing it would mean removing the power feed from the mill table.

Ed

   
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#36
02-08-2015, 03:53 PM
I used Lubriplate (white lithium grease) on mine Ed. Coat the bevel gears with it too.
Willie
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#37
02-08-2015, 04:29 PM
(02-08-2015, 03:53 PM)Highpower Wrote: I used Lubriplate (white lithium grease) on mine Ed. Coat the bevel gears with it too.

Good, I have a tube of that and was going to use it. Smile

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#38
02-08-2015, 05:01 PM
Looking good Ed
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#39
02-08-2015, 05:03 PM
Very nice work Ed Thumbsup Smiley-signs107

Smiley-eatdrink004 
DaveH
Reply
Thanks given by: EdK
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#40
02-08-2015, 07:06 PM
Looking great Ed!

Being far too anal, I would run around the big square piece with a corner rounding cutter to smooth it out. Then I'd be at it with my ScotchBrite wheel to make it look more like a casting. I might even look for an anodizer to get it some cool color.
Reply
Thanks given by: EdK




Users browsing this thread: 2 Guest(s)