Coke Forge Build
It does look good Rob Thumbsup 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
(04-14-2015, 04:48 PM)hermetic Wrote: Hi Rob, superb quality workmanship, but I hope you are going to put a speed control on the fan, or there will be red hot coke flying up the chimney!! I have an old school Allday (literally, it came from an old school) which put my back out lifting the tuyere and tank of the back of my truck. It is in a corner awaiting ressurection.
Phil

Hi there Phil . I would love an Alldays just don't have the room .I am making a wee butterfly valve to control the air flow .


Cheers Rob
Reply
Thanks given by:
Evening Lads  




Made a start on the ash dump today ,plasma cut the parts from 6mm and 12 mm stainless . On my state of the art plasma table LOL . 


[Image: P1080804_zpsnftawdfm.jpg]
[Image: P1080808_zpsmvlu6d7v.jpg]

And after a  bit of a clean up . Sorted !

[Image: P1080822_zpsjg51wxj3.jpg]
[Image: P1080819_zpsckwvygjg.jpg]

Rob 
Reply
Thanks given by:
Your state of the art plasma table worked very well, Thumbsup  just don't wear sandals Big Grin 

  Smiley-signs107 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
Seriously Dave !   Slaphead   ,,,,,,,,,,,,,,,,,,,,,, who the F%$k wears saddles in the UK    Chin  flower power died in the 60's  Big Grin



Rob 
Reply
Thanks given by:
(04-28-2015, 02:35 PM)RobWilson. Wrote: flower power died in the 60's  Big Grin

Rob 

Yes, but I didn't Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
You must have a steady hand rob to get those cuts. And nice cuts for stainless.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Remember Greg, it's all in the camera. Rotfl

Steve

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
A bit more done today   Big Grin , worked on the air control valve spindle , this was turned and screw cut , then slapped onto the mill like so .


[Image: P1010215_zpsuaqfz0fe.jpg]

Two flats mill on the screwed section .

[Image: P1010219_zpsrwjlyx7s.jpg]
[Image: P1010221_zpsrszlcvm0.jpg]

Then a section of spindle was milled away for the gate /butterfly .

[Image: P1010232_zpsnnjswpfw.jpg]

And then a couple of hole were poked in .

[Image: P1010236_zpspwjbw2yi.jpg]


Next a 1 mill thick disc was turned , this needs two slots milled . I used an old bearing race to centre the chuck with the aid of my Zero set indicator (Wilson copy) , just love that tool .  Cool

[Image: P1010243_zpsbnmofldj.jpg]

Then the disc mounted and milled .

[Image: P1010248_zpsvfjplewf.jpg]


Nearly there . 

[Image: P1010252_zpso868mlw8.jpg]
[Image: P1010249_zpsk7rzvvdv.jpg]


Rob   Popcorn
Reply
Thanks given by:
VERY nice work Rob, as usual, or is it as expected.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)