Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Thanks DA,
That is the correct manual.
I'll have another read, the thing that confuses me is I have two wires from the start button, and two wires from the stop button. So do I put one wire from the start to S1 and one wire from the stop to S2 and then common the remaining two wires to GND?
DaveH
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
Dave, is the "start" button a "normally open" switch and the "stop button" a "normally closed" switch?
Also, NEVER have any switches or circuit breaking device between the VFD (inverter) and the motor.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
05-30-2014, 12:30 PM
(This post was last modified: 05-30-2014, 12:39 PM by stevec.)
Today I decided to cut the stump of one of the oaks I took down on our front lawn.
Here it is ready to test the log lifter on my splitter.
I think I'll try and rotate it to a better position for the first split.
This looks a bit better.
That is better, still had to help complete the separation with a few whacks of the axe.
Here's the second split, things are getting a bit more workable now.
a little more work and we have wheel barrow overload with stackable (sorta) firewood.
More work than I counted on, I`ll leave the second stump til tomorrow.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
05-30-2014, 12:43 PM
(This post was last modified: 05-30-2014, 12:57 PM by DaveH.)
Steve,
The Stop and Start push buttons I have can be either normally open or normally closed.
I understand nothing is to go in between the inverter and the motor.
I don't have to put in a start and stop push button at this time for the log splitter. However in the future when I change the lathe motor I will want a stop, start button, reversing switch and speed control and read out.
DaveH
PS I didn't buy the stop and start buttons for this particular job, I've had them laying about for years.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Nicely done Steve.
Your control valve is it a detent type?
DaveH
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
(05-30-2014, 06:47 AM)stevec Wrote: I hear ya Dave, I too am trying to "translate" the chinglish manual that came with my VFD. 
Steve,
What are you trying to do with your VFD? I'll try to help out.
Ed
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
(05-30-2014, 01:19 PM)EdK Wrote: What are you trying to do with your VFD? I'll try to help out.
Ed
Hi Ed,
Just trying to understand how to wire in a stop and start button into the VFD, and where to connect all the wires to.
One would think in a manual of 100 pages there would be:
1) How to wire in a STOP button
2) How to wire in a START button.
3) How the wire in a REVERSING switch.
They are there just not clear to me
DaveH
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
These instruction are not for my inverter, nevertheless instructions like this I can nearly understand. I say nearly because are the start and stop buttons both normally open?
DaveH
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
(05-30-2014, 01:45 PM)DaveH Wrote: Hi Ed,
Just trying to understand how to wire in a stop and start button into the VFD, and where to connect all the wires to.
One would think in a manual of 100 pages there would be:
1) How to wire in a STOP button
2) How to wire in a START button.
3) How the wire in a REVERSING switch.
They are there just not clear to me
DaveH
Dave,
I can help you. I didn't respond because you said you weren't going to wire those in on the log splitter but on your lathe later on. I'll draw something up and post it.
Ed
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 1 user Likes EdK's post:
Highpower (06-06-2014)
(05-30-2014, 02:11 PM)DaveH Wrote: These instruction are not for my inverter, nevertheless instructions like this I can nearly understand. I say nearly because are the start and stop buttons both normally open?
DaveH
Dave,
You always want the stop button to be a normally closed button. That way if a wire breaks in the stop button circuitry it'll look like you pressed the stop button which is what you want for safety purposes.
Ed
