MetalworkingFun Forum › Machining › How-To's v
How to Make Custom Length Bandsaw Blades Without Welding

Thread Modes
How to Make Custom Length Bandsaw Blades Without Welding
the artfull-codger Offline
Sophmore
***
Posts: 184
Threads: 21
Joined: Feb 2013
Location: north yorkshire n.e.england
#21
02-02-2014, 04:23 PM (This post was last modified: 02-02-2014, 04:25 PM by the artfull-codger.)
(01-25-2014, 03:09 PM)TomG Wrote: You know what they say Graham, if there aren't pictures then it never happened. Thumbsup

Tom

ha ha I'll put ''the proof'' on here in a couple of days Tom when I photograph
them.
Graham.
the artfull-codger, proud to be a member of MetalworkingFun Forum since Feb 2013.
Reply
Thanks given by:
chucketn Offline
Junior
****
Posts: 375
Threads: 53
Joined: Jun 2013
Location: Jonesborough, TN
#22
02-05-2014, 08:48 PM
Worked on my jig today. Got the basic plate done with soldering notch and 20° slot. I need to buy some 1/4" x 3/4" stock for the key.
Where did you find the toggle clamps you used?

Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#23
02-05-2014, 08:59 PM
Mine came from McMaster Carr, but any industrial supply will carry them (Reid, MSC,Grainger, etc.)

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
chucketn Offline
Junior
****
Posts: 375
Threads: 53
Joined: Jun 2013
Location: Jonesborough, TN
#24
02-05-2014, 09:05 PM
Did they have the leg on them that contacts the blade, or did you add that?
Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#25
02-05-2014, 10:07 PM
They come with a screw. You have to add any special fixturing.
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
chucketn Offline
Junior
****
Posts: 375
Threads: 53
Joined: Jun 2013
Location: Jonesborough, TN
#26
02-06-2014, 08:07 AM
(02-05-2014, 10:07 PM)TomG Wrote: They come with a screw. You have to add any special fixturing.

Thanks, Tom.
Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
Reply
Thanks given by:
chucketn Offline
Junior
****
Posts: 375
Threads: 53
Joined: Jun 2013
Location: Jonesborough, TN
#27
02-24-2014, 02:45 PM
Got my jig finished today. Works as advertized. Just happened to have saved a couple of broken blades to practice on. Found out the solder I used isn't high enough in silver content to make a good joint, it broke easily when I was trying to coil the repaired blade to store it.
I know I have some better solder somewhere, just got to find it and try it.

Chuck
Micromark 7x14 Lathe, X2 Mill , old Green 4x6 bandsaw
The difficult takes me a while, the impossible takes a little longer.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#28
02-24-2014, 05:34 PM
Sounds good Chuck, how about some pics?

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#29
02-25-2014, 06:59 AM
Smiley-signs009
Hunting American dentists since 2015.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#30
02-25-2014, 08:06 PM
Gave it a try today. Made a jig with two different width slots, figure the wood cutting blades have so much set you'd need to support them back of the teeth.
This was a broken one from the 4 x 6 saw.

[Image: IMG_1051.jpg]

Now trying to track down blade stock, not as easy to find in Canukastan
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)