Woodcarving a pointer dog
#21
(02-23-2014, 05:49 PM)doubleboost Wrote: Great job Mick
It needs the left nacker dropping 23 thou
John

Rotfl
Reply
Thanks given by:
#22
Hi All , I have finally got around to finishing the carving of the pointer dog, its ended up more of a German Shorthaired pointer rather than a Wirehaired like my dog but that was mainly down to time to try and get it finished . I am planning at some point on doing a bit larger carving of my dog with the rough coat.

From the point I left off, I just had to refine the shape and contours of the dog, you can not see that much in the photos probably but more or less every part was altered. I used carving tools , riffler and needle files dremel type tools and lots of careful sanding.

[Image: PointerandHarecarvings038.jpg]

[Image: PointerandHarecarvings039.jpg]

Once the main body was done it was time for the head and the worst part the eyes, this is the head ready for the eyes to be done.

[Image: PointerandHarecarvings045.jpg]

First I drew the eyes on making sure they looked even and spaced in the right place each side, as you can see in the background I am using a tablet to view a photo for reference.

[Image: PointerandHarecarvings051.jpg]

They came out ok but I needed smaller tools than I had really so I think if I did them again I would like to have done them not quite as deep set but overall they look pointer like and the face still has the right look about it.

[Image: PointerandHarecarvings054.jpg]

[Image: PointerandHarecarvings060.jpg]

This was the dog ready for final sanding but I was not happy with the base , the dog is standing in what should be long grass or heather, so I decided to re do the whole surface of the base so it looked more like flowing long grass, this is it before.

[Image: Pointerdogfinished003.jpg]

[Image: Pointerdogfinished004.jpg]

This is the new base with the grass like texture, I think it looks much better than the tooled finish it had before.

[Image: Pointerdogfinished015.jpg]

A mix of beeswax and pure turpentine was then scrubbed in with an old toothbrush, then the carving warmed with an electric heat gun so the wax went liquid and soaked into the wood, this is it before being heated.

[Image: Pointerdogfinished019.jpg]

This is the finished thing after buffing up, the first shots are in the shed and the last are in the house where I thought the light would be better but I am not sure it was really.

[Image: Pointerdogfinished029.jpg]

[Image: Pointerdogfinished031.jpg]

[Image: Pointerdogfinished032.jpg]

[Image: Yorkshireshow019.jpg]

[Image: Yorkshireshow022.jpg]

[Image: Yorkshireshow013.jpg]

So job done in the end, I have lost track totally of how long its taken but I bet a full week say 40-50 hours ? The main problem with the woodcarving is there is no going back once you take wood off its gone , so you spend a lot of time deciding if its safe to remove more and which bits need to be reshaped, no doubt the longer you have been carving the faster you will be able to decide.

Cheers Mick.
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
#23
I have seen this carving in the flesh (wood)
Sadly the pictures do not do it justiceWorthyWorthyWorthy
I was blown away by the detail
The left nacker is still 25 thou to low YikesYikesYikes
John
Reply
Thanks given by:
#24
Nice work Mick! I like the way you made the base look like the dog is standing in grass. Thumbsup

Ed
Reply
Thanks given by:
#25
That is an amazing job Mick. The detail on the raised paw pad shows the time and skill invested into this.

John - one should always hang a little lower...
Hunting American dentists since 2015.
Reply
Thanks given by:
#26
Wonderful work Mick! I can almost see him quivering with anticipation.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#27
Smiley-signs107 new style grass looks allot better Mick ,top job Smile


Rob
Reply
Thanks given by:
#28
Amazing work Mick ThumbsupWorthy
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#29
in a word thats the dogs do dars mate well dun
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#30
Hi Lads thanks for the compliments WorthyWorthy Glad to see you are back on line Bob Smile

I still plan on doing a Wirehaired version of a pointer dog carving at some point but wil practice on the detailing work first.
Cheers Mick
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:




Users browsing this thread: 8 Guest(s)