Lathe spindle degree wheel pics
#1
Here is how i made my degree wheel for indexing my spindle. I used a stick on 4" wheel from http://www.mcmaster.com/#protractor-dials/=gulle8 and some 4" aluminum bar stock that i have on hand. The one pic is the cutter since the degree wheel only had a 5/8" center hole and i needed bigger so i made a cutter with a 5/8" center pin and tapered the cutting edge to make a smooth cut when wacked lightly with a hammer. I did it right on my wifes counter top with another alum disc with a 5/8" hole in the center underneath it. The aluminum was turned on an arbor then bored to fit my spindle end. Enjoy...Bob


Attached Files
.jpg   n_aCAGBUPUP.jpg (Size: 30.54 KB / Downloads: 149)
.jpg   n_aCAH5GT7F.jpg (Size: 34.23 KB / Downloads: 149)
.jpg   n_aCAFAMBLG.jpg (Size: 13.01 KB / Downloads: 150)
.jpg   n_aCA6Y89I8.jpg (Size: 53.82 KB / Downloads: 149)
.jpg   n_aCAK29ZYG.jpg (Size: 31.73 KB / Downloads: 151)
.jpg   n_aCAHSHOG4.jpg (Size: 23.37 KB / Downloads: 148)
.jpg   n_aCAG6CWN5.jpg (Size: 40.17 KB / Downloads: 148)
.jpg   n_aCA1X1J3E.jpg (Size: 33.14 KB / Downloads: 149)
.jpg   n_aCAI7ICBP.jpg (Size: 23.72 KB / Downloads: 148)
.jpg   n_aCACKXDON.jpg (Size: 38.61 KB / Downloads: 148)
.jpg   n_aCA1WVNB8.jpg (Size: 23.57 KB / Downloads: 151)
.jpg   n_aCAFKS5X0.jpg (Size: 34.06 KB / Downloads: 149)
.jpg   n_aCA1P742P.jpg (Size: 34.5 KB / Downloads: 152)
.jpg   n_aCAJOLTJ9.jpg (Size: 25.39 KB / Downloads: 150)
.jpg   n_aCA849QGQ.jpg (Size: 29.16 KB / Downloads: 148)
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:
#2
And if anyone needs some aluminum wool like steel wool i have a bundle of it...Bob


Attached Files Thumbnail(s)
   

.jpg   n_aCAP7NX8A.jpg (Size: 26.72 KB / Downloads: 148)
.jpg   n_aCATGDEFJ.jpg (Size: 24.53 KB / Downloads: 144)
.jpg   n_aCASVP5CW.jpg (Size: 24.37 KB / Downloads: 148)
.jpg   n_aCATJKZ83.jpg (Size: 23.57 KB / Downloads: 145)
.jpg   n_aCATS15SC.jpg (Size: 33.67 KB / Downloads: 146)
.jpg   n_aCAMUNUWN.jpg (Size: 24.94 KB / Downloads: 148)
.jpg   n_aCAVTWM5O.jpg (Size: 34.48 KB / Downloads: 144)
.jpg   n_aCATD8SQX.jpg (Size: 25.15 KB / Downloads: 146)
.jpg   n_aCAPGBPJP.jpg (Size: 19.07 KB / Downloads: 147)
.jpg   n_aCATKEKVF.jpg (Size: 25.34 KB / Downloads: 145)
.jpg   n_aCALLEIWE.jpg (Size: 25.49 KB / Downloads: 147)
.jpg   n_aCAYG9IFZ.jpg (Size: 18.01 KB / Downloads: 144)
.jpg   n_aCAX8WC49.jpg (Size: 16.53 KB / Downloads: 144)
.jpg   n_aCAYRX407.jpg (Size: 31.78 KB / Downloads: 146)
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:
#3
Last one...Bob


Attached Files
.jpg   n_aCAZC7XZB.jpg (Size: 24.77 KB / Downloads: 146)
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:
#4
Bob,

Nice thread and thanks for the source for the degree wheels. I'd like to add an indexing feature to my lathe some day and this thread will be of great help. Smiley-signs107

Ed
Reply
Thanks given by: aametalmaster
#5
ooo i will have to look for them in the uk a brill post thanks bob from bob
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by: aametalmaster
#6
I see they come in clockwise and counter clockwise formats. Yours appears to be the clockwise format. If you had it do over again is that the format you would choose or would you get the counter clockwise format?

Or to put it another way, is the clockwise format a natural way to use it or do you find yourself doing math to git-er-don.
Reply
Thanks given by:
#7
(03-28-2012, 02:10 PM)arvidj Wrote: I see they come in clockwise and counter clockwise formats. Yours appears to be the clockwise format. If you had it do over again is that the format you would choose or would you get the counter clockwise format?

Or to put it another way, is the clockwise format a natural way to use it or do you find yourself doing math to git-er-don.
Either direction is fine for this project.
I had the numbers wrote down for my faceplate before i started drilling so i wouldn't get confused. Here is my cheat sheet LOL Ya caught me...Bob


Attached Files
.jpg   pattern.jpg (Size: 22.16 KB / Downloads: 113)
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)