Homemade 20 ton hydraulic press
#21
(04-09-2012, 02:17 PM)EdAK Wrote:
(03-21-2012, 11:02 AM)TOM REED Wrote: I will take a better pic when i8 get home to show the top of the press....

Tom,

When you get a chance, could you please post a picture of the top of the press? I need to make or buy one soon and could use all of the ideas I can get.

Thanks,
Ed
Here are thi pics of the top end of my press, it is now about 25 yrs old and has never let me down. I like this design it is very stable under pressure, I have used it with lots of pressure and things let go with loud bang as the bearing or piece lets go. I or my staff in the towing company never managed to hurt it. I would copy it or buy another in a heartbeat. tom

Excuse the dust the top bar is 2 inch square, the vertical rods are 3/4 inch in dia, the plate the jack sits on is 3/8 inch, the shaft under the jack is 2 inch dia with a hardened foot, the springs are about 2.5 or 3 inch and could be rescued from coil over shocks and I think all the channel is 5 inch. The moveable support that you place the workpiece on is reinforced with what appears to be 3/8 x5 flat for about 3/4 of the way across, this is welded on one side to the inside bottom of the channel and the other side on a diagonal is just below top surface. Hope this helps. tom


Attached Files Thumbnail(s)
                           
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#22
Nice design Tom.
Greg
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#23
(04-09-2012, 09:51 PM)f350ca Wrote: Nice design Tom.
Greg

It is a commercial design I think made by HEIN WERNER. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#24
Tom,

That is a clever one, someone put quite a bit of thought in to it.SmileSmileSmile
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#25
Tom,

Sorry about the late response, I didn't see your post until this evening. What is the jack for that sits on top to the left of the working jack?

Thanks,
Ed
Reply
Thanks given by:
#26
That is one of 2 20 ton air operated bottle jacks I use when lifting my truck, also handy when doing heavy pushes with the press. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#27
    Here's mine I built it a few years back , used it often.
Reply
Thanks given by:
#28
Can you say BEEFY???

Wow, very nice! I like the press brake sitting on the floor as well. Thumbsup

Willie Smiley-signs046
Willie
Reply
Thanks given by:
#29
(07-27-2012, 11:19 PM)Highpower Wrote: Can you say BEEFY???

Wow, very nice! I like the press brake sitting on the floor as well. Thumbsup

Willie Smiley-signs046

Thanks I just joined this site , lots of good ideas here to add to my never ending list of things to build
Reply
Thanks given by:
#30
Bill,
Nice press, like your guide system ThumbsupThumbsupThumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)