Shop Press
(05-04-2014, 04:46 PM)EdK Wrote:
(05-04-2014, 04:13 PM)f350ca Wrote: VERY !!!!!!!!

If it isn't you're not in line with the ram so you'll be pressing bearings in askew, and if you need to use a spacer it can kick out real easy.
...

Greg,

That's kind of what I thought. I can't get mine square the way it is so I'll need to elongate some holes. Bummer! Angry

Ed

I think it should be put together first and see if the 'ram' is perpendicular to the table.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Maybe turn the table around end for end, and/or flip it over and see if it lines up better? Chin
Willie
Reply
Thanks given by:
(05-04-2014, 06:31 PM)DaveH Wrote: I think it should be put together first and see if the 'ram' is perpendicular to the table.
Smiley-eatdrink004
DaveH

Dave,

It is put together. That's how I know it's not square.

Ed
Reply
Thanks given by:
Slaphead Slaphead Slaphead
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Anybody have any idea how much CFM this air over hydraulic jack would need to operate? HF only lists the maximum PSI but no CFM specs. 17428

http://www.harborfreight.com/http-www-ha...-html.html

Ed
Reply
Thanks given by:
I have no idea what the CFM requirement is on the HF 20 ton I put on mine but my gut tells me "not very much" and "it was a great addition".

I have air over hydraulic on both the engine hoist and the shop press. They both go "pht ... pht ... pht ... pht" when you apply the air. Obviously it is the air being released from the chamber with each stroke of the piston. I suspect that in a pinch I could run either of them to full extension several times with nothing more than a full portable air tank and no compressor at all.

I think I have the air lines regulated below 130 or less and I'm sure anything more than 80-90 will work. If nothing else it saves all the pumping to take up the slack and then you can go for the gold with just a couple of manual strokes.

In short, if your compressor can not keep up with the jack you may have trouble filling a tire with it.

But that is just my non-scientific opinion.
Reply
Thanks given by: EdK
My non-scientific opinion concurs with arvidj's. Thumbsup
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: EdK
(05-06-2014, 05:51 PM)arvidj Wrote: I have no idea what the CFM requirement is on the HF 20 ton I put on mine but my gut tells me "not very much" and "it was a great addition".

I have air over hydraulic on both the engine hoist and the shop press. They both go "pht ... pht ... pht ... pht" when you apply the air. Obviously it is the air being released from the chamber with each stroke of the piston. I suspect that in a pinch I could run either of them to full extension several times with nothing more than a full portable air tank and no compressor at all.

I think I have the air lines regulated below 130 or less and I'm sure anything more than 80-90 will work. If nothing else it saves all the pumping to take up the slack and then you can go for the gold with just a couple of manual strokes.

In short, if your compressor can not keep up with the jack you may have trouble filling a tire with it.

But that is just my non-scientific opinion.

Rotfl

Thanks Arvid. I was hoping that would be the case. I'm going to get this compressor for now and upgrade later, if necessary.

http://www.menards.com/main/tools-hardwa...-12910.htm

With a "25% off one item" coupon floating around I thought I'd get the air over hydraulic jack. I have the winch coming this week also.

Ed
Reply
Thanks given by:
I wouldn't have thought that you would need to worry about CFM in this application, as you would not be running it continuesly. Air tools on the other hand are notoriously hungry and therefore specify necessary air supply. Nothing is more annoying than using a die grinder for 10 seconds and having it lag and the compressor kick on again.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
(05-07-2014, 07:16 AM)EdK Wrote:
(05-06-2014, 05:51 PM)arvidj Wrote: ...
In short, if your compressor can not keep up with the jack you may have trouble filling a tire with it.
...
Rotfl
...
I'm going to get this compressor for now and upgrade later, if necessary.

http://www.menards.com/main/tools-hardwa...-12910.htm
...
Ed

And one of the key features of this compressor is that is has "Never-flat tires for maximum durability" so you never have to worry about its ability to fill a tire Big Grin
Reply
Thanks given by:




Users browsing this thread: 6 Guest(s)