04-24-2015, 08:56 PM
Looking good 
DaveH
DaveH
|
Fire Wood Processor
|
04-27-2015, 07:06 PM
Finished up the arm that the bar mounts to and the chain tensioner.
![[Image: IMG_1706.jpg]](https://lh3.googleusercontent.com/--fFhC6k2Eik/VT7OVH7hLMI/AAAAAAAAC6w/oFo4BSzHbdk/s1280/IMG_1706.jpg) ![[Image: IMG_1705.jpg]](https://lh3.googleusercontent.com/-sbSTtRmTMkg/VT7OT0JtcHI/AAAAAAAAC6s/gNXOj5S6H0A/s1280/IMG_1705.jpg) Lots of metal whittling. ![[Image: IMG_1708.jpg]](https://lh3.googleusercontent.com/-JwhIyb-oC9E/VT7OUbIhI2I/AAAAAAAAC60/hqWTLILa_gU/s1280/IMG_1708.jpg)
Free advice is worth exactly what you payed for it.
Greg 
04-27-2015, 07:34 PM
That is one big saw bar! Top class work as always Greg
Hunting American dentists since 2015.
Thanks given by: f350ca
04-28-2015, 06:18 AM
Greg, have you mentioned how you plan to power the saw? (memory is the first thing to go, or is it the second?
 )Steve
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
04-28-2015, 06:35 AM
hydraulics is the way to go, the feed conveyor, and the cylinder that rotates the saw bar is powered by hydraulic.
DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
04-28-2015, 01:10 PM
I think all the commercial units are hydraulic driven, but I need to be different. Between the pump and motor your probably loosing half your power to heat, plus 7400rpm hydraulic motors get real expensive. Going to set it up with a belt drive from an electric clutch.
Free advice is worth exactly what you payed for it.
Greg
04-28-2015, 02:31 PM
That be a dam fine bit of metal whittling Greg
 Rob Thanks given by: f350ca
04-29-2015, 05:47 AM
Sorry to be a nitpicker Greg but, what drives the clutch?
 Steve
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
04-29-2015, 09:26 AM
Steve, Im planning on using that Wisconsin to power the machine but and there's always a BUT, some cuter than others mind. All the commercial ones have much bigger engines, 40 to 80 hp range might be a manly thing as I can't see where the power is used. Oregon has charts on everything about their Harvester chains, 10 hp should give a really good material removal rate, and the splitter which won't be working when the saw is should only need maybe 8 hp.
Anyway, in case the 14 hp isn't enough I'll run a driveshaft off it to a jack shaft where I can run one of the two pumps, then belts to speed up a second jack shaft that will carry the clutch and the second pump. If I need a bigger engine it would be a lot easier to convert with the driveshaft drive. The Wisconsin revs at 2800 RPM, which will drive the small pump for the cylinders and such, the second jack shaft will run at 3600 RPM for the clutch and splitter pump. Then speed up off the clutch to 7400 RPM for the saw to give a chain speed of 8000 feet per minute (Oregon's recommended speed) Probablty a lot more info than you asked for but thats the current plan.
Free advice is worth exactly what you payed for it.
Greg |
|
« Next Oldest | Next Newest »
|
Users browsing this thread: 6 Guest(s)