Minimal Clockmaking
#11
Now a chuck back plate.

   

It fits the center hole of the drill base.

   

And the angle bracket

   

Very useful.

More small tools as we go along .Sorry about the cost of the protractor, Perhaps you could mug a student? or steal from the kids.6799

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
#12
Now the painful part the clock has 5 gears 2 escapement wheels and a ratchet that must be made of engraving quality brass , well the ratchet possibly could be steel!!! it goes against the grain to spend money but its a must.


So we will start with the simplest one.
The ratchet only has 10 teeth and the back slope is cut by hand.

   

wonderfull the slot cutter works!!Thumbsup

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
#13
Brian,
How thick is the brass? And how do you cut those slots? Do you start at the top and "nibble" you way down or is it full depth and one pass?
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#14
The blank is 1/16" thick Dave and it was cut in one pass.

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
#15
Thanks Brian,
Looking at the pics those slots don't seem to be on a centre line are they offset?
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#16
Brian,

Mr. Goldberg would be right proud! It is amazing what can be done with minimal tooling and a little ingenuity.

Can't wait to see more. Popcorn

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#17
(12-04-2012, 06:29 AM)DaveH Wrote: Thanks Brian,
Looking at the pics those slots don't seem to be on a centre line are they offset?
Smiley-eatdrink004
DaveH

Yes Dave, its to get the hook in the tooth that holds the pawl.

brian
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
#18
Really nice work, enjoyable viewing. Thanks for the pics and info.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
#19
I'm assuming that there will be some plans at some point to help build the clock with?

nice work, clocks have always fascinated me ever since I took mom's alarm clock apart and didn't get it back together just exactly right for some reason it would skip a couple hours during the day Big GrinBig GrinBig GrinBig Grin
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#20
(12-04-2012, 02:17 PM)dallen Wrote: I'm assuming that there will be some plans at some point to help build the clock with?

nice work, clocks have always fascinated me ever since I took mom's alarm clock apart and didn't get it back together just exactly right for some reason it would skip a couple hours during the day Big GrinBig GrinBig GrinBig Grin

Hi Dallen
This clock is the prototype to work out any bugs. I am taking loads of photos and will write full instructions on its build including plans.
In accordance with the name of this article they will be inexpensive. and I will also give a consulting service to those who require help.
I am open to any suggestions.
Brian
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)