MetalworkingFun Forum › Machining › General Metalworking Discussion v
Hardinge Lathe

Thread Modes
Hardinge Lathe
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#51
03-14-2014, 06:14 PM
Nice! Is that a 5C collet?

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#52
03-14-2014, 06:52 PM
Yep, the spindle is ground to fit them, the dead centre is formed on a 5c mount. Need to make a pin spanner to fit the chucks to tighten and remove. Haven't seen a picture of one, could you post a picture of yours Tom, would be appreciated.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
stevec (03-17-2014)
#53
03-16-2014, 09:52 PM (This post was last modified: 03-16-2014, 09:53 PM by f350ca.)
Tackled repairing the damaged pinion that drives the carriage.
Cut a new gear from a salvaged strut rod.

[Image: IMG_1092.jpg]

Machined away the damaged gear.

[Image: IMG_1094.jpg]

Did a shrink fit with 1 1/2 thou interference.

[Image: IMG_1095.jpg]

For reassurance I drilled the joint a put a 1/16 spring pin in to act as a key.

Finished assembling it today.

[Image: IMG_1097.jpg]

Was a little worried the new cut gear might put a pattern in the surface if the teeth weren't formed correctly, but all seams to be fine.

[Image: IMG_1099.jpg]

Im getting about 1/2 thou taper in 8 inches. guess the tailstock needs tweaked.

The silence of it is a little unnerving after being accustomed to gear head lathes. All in all looks like its going to be a good machine.
Thanks for watching
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#54
03-16-2014, 10:29 PM
Greg,

You did an absolutely AMAZING job with the refurbishing! Your attention to detail is tops, and it looks as good or better than factory new.
Reply
Thanks given by: f350ca
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
#55
03-17-2014, 01:06 AM
That finish is incredible, and the lathe looks amazing.
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by: f350ca
EdK Offline
Whipping Boy
*******
Posts: 8,859
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#56
03-17-2014, 06:22 AM
Nice use of soft jaws. Thumbsup

You did an amazing job of refurbishing the lathe in such a short period of time.

Ed
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#57
03-17-2014, 04:54 PM
Guess it was only a two week turn around Ed, seemed a lot longer.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#58
03-17-2014, 06:09 PM
Greg,

I'll send you a drawing of the wrench.

There is no adjustment on the tailstock, it's ground to fit. You probably just need to clean and lube the front of the way and matching dovetail.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (03-18-2014)
#59
03-17-2014, 07:14 PM
Thats what I thought Tom, but this one has an adjustable gib on the front side. Im assuming its to make adjustments.
Thanks on the wrench offer.
Tried threading with it today, Oh My God, there's going to be treads on everything I can think of.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#60
03-18-2014, 06:04 PM
Well I'll be damned, there is a gib under there. Guess it's been a while since I've looked. Nev-r-mind.

Yes, you will LOVE it for threading. I hardly ever drag the dies out any more because it's nearly as quick and a heck of a lot more fun to single point them on the Hardinge.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)