Saw Mill
#39
Not sure about faster but a little heavier.
Got back to this project. A 7 inch cutoff disk made a clean separation of the old base. I blocked one end of the new members and use a machinist jack and precision level to get them flat. The carriage was then positioned and angle plates clamped to the uprights so I could use the level to get them plumb. Used turnbuckles and chains for the final adjustments.
Back in one piece.

[Image: 4zaV3kTcgxbtzwfqlDO0xJpAIE9ZNLqtYfCksmJh...9-h1267-no]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
Saw Mill - by f350ca - 04-08-2012, 12:42 AM
RE: Saw Mill - by doubleboost - 04-08-2012, 05:50 AM
RE: Saw Mill - by aametalmaster - 04-08-2012, 07:43 AM
RE: Saw Mill - by DaveH - 04-08-2012, 12:00 PM
RE: Saw Mill - by ETC57 - 04-08-2012, 12:05 PM
RE: Saw Mill - by f350ca - 04-08-2012, 12:46 PM
RE: Saw Mill - by ETC57 - 04-08-2012, 07:43 PM
RE: Saw Mill - by stevec - 04-09-2012, 07:03 AM
RE: Saw Mill - by f350ca - 05-30-2012, 05:16 PM
RE: Saw Mill - by krv3000 - 05-31-2012, 04:26 PM
RE: Saw Mill - by EdK - 05-31-2012, 05:00 PM
RE: Saw Mill - by DaveH - 05-31-2012, 05:03 PM
RE: Saw Mill - by f350ca - 06-07-2012, 05:51 PM
RE: Saw Mill - by stevec - 06-07-2012, 06:12 PM
RE: Saw Mill - by DaveH - 06-07-2012, 06:21 PM
RE: Saw Mill - by ETC57 - 06-07-2012, 07:16 PM
RE: Saw Mill - by Mayhem - 06-07-2012, 08:06 PM
RE: Saw Mill - by f350ca - 06-07-2012, 09:58 PM
RE: Saw Mill - by EdK - 06-08-2012, 06:09 AM
RE: Saw Mill - by krv3000 - 06-08-2012, 10:20 AM
RE: Saw Mill - by ETC57 - 06-08-2012, 10:49 AM
RE: Saw Mill - by f350ca - 06-08-2012, 12:58 PM
RE: Saw Mill - by RobWilson - 06-08-2012, 02:36 PM
RE: Saw Mill - by doubleboost - 06-08-2012, 03:36 PM
RE: Saw Mill - by Mayhem - 06-09-2012, 10:57 AM
RE: Saw Mill - by DaveH - 06-09-2012, 02:50 PM
RE: Saw Mill - by Rickabilly - 06-11-2012, 08:22 AM
RE: Saw Mill - by krv3000 - 06-11-2012, 08:32 AM
RE: Saw Mill - by stevec - 06-11-2012, 03:33 PM
RE: Saw Mill - by DaveH - 06-11-2012, 03:36 PM
RE: Saw Mill - by stevec - 06-12-2012, 06:25 AM
RE: Saw Mill - by f350ca - 06-11-2012, 07:10 PM
RE: Saw Mill - by Rickabilly - 06-12-2012, 05:42 AM
RE: Saw Mill - by stevec - 06-12-2012, 06:33 AM
RE: Saw Mill - by f350ca - 06-12-2012, 09:50 AM
RE: Saw Mill - by krv3000 - 06-12-2012, 02:44 PM
RE: Saw Mill - by f350ca - 07-09-2018, 09:53 PM
RE: Saw Mill - by Highpower - 07-09-2018, 11:53 PM
RE: Saw Mill - by f350ca - 07-17-2018, 09:27 PM
RE: Saw Mill - by JScott - 07-18-2018, 06:52 AM
RE: Saw Mill - by Highpower - 07-18-2018, 01:34 PM



Users browsing this thread: 1 Guest(s)