MetalworkingFun Forum › Machining › General Metalworking Discussion v
Cutting Holes In Sheetmatal

Thread Modes
Cutting Holes In Sheetmatal
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 4 users Like EdK's post:
f350ca (05-28-2016), Mayhem (05-28-2016), DaveH (05-29-2016), arvidj (05-29-2016)
#38
05-28-2016, 04:26 PM
Finally got some time to tackle this. Got the first large hole done. It went much smoother than I expected. I used the hole saw with my 1/2" power drill. The other one will have to wait until tomorrow.

Ed

   
Reply
Thanks given by:


Messages In This Thread
Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:23 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:33 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:40 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:45 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:28 PM
RE: Cutting Holes In Sheetmatal - by f350ca - 05-17-2016, 04:48 PM
RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-17-2016, 04:59 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:27 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-17-2016, 05:40 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-17-2016, 09:55 PM
RE: Cutting Holes In Sheetmatal - by TomG - 05-17-2016, 05:44 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 06:05 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 06:13 PM
RE: Cutting Holes In Sheetmatal - by wawoodman - 05-17-2016, 06:53 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 07:39 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 07:46 PM
RE: Cutting Holes In Sheetmatal - by arvidj - 05-17-2016, 08:46 PM
RE: Cutting Holes In Sheetmatal - by Dr Stan - 05-17-2016, 10:58 PM
RE: Cutting Holes In Sheetmatal - by Hawkeye - 05-17-2016, 11:09 PM
RE: Cutting Holes In Sheetmatal - by awemawson - 05-18-2016, 03:16 AM
RE: Cutting Holes In Sheetmatal - by EdK - 05-18-2016, 05:31 AM
RE: Cutting Holes In Sheetmatal - by rleete - 05-18-2016, 09:01 AM
RE: Cutting Holes In Sheetmatal - by Mayhem - 05-18-2016, 09:29 AM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 07:12 AM
RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-18-2016, 12:01 PM
RE: Cutting Holes In Sheetmatal - by PixMan - 05-18-2016, 01:20 PM
RE: Cutting Holes In Sheetmatal - by dallen - 05-18-2016, 05:50 PM
RE: Cutting Holes In Sheetmatal - by PixMan - 05-19-2016, 06:12 AM
RE: Cutting Holes In Sheetmatal - by the penguin - 05-19-2016, 09:04 AM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 03:28 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 06:10 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 06:49 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 06:57 PM
RE: Cutting Holes In Sheetmetal - by EdK - 05-19-2016, 07:18 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 07:13 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 07:19 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 08:34 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-28-2016, 04:26 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-28-2016, 06:18 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-28-2016, 08:27 PM



Users browsing this thread: 8 Guest(s)