+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Cutting Holes In Sheetmatal (/thread-3177.html)
Cutting Holes In Sheetmatal - EdK - 05-17-2016
I need to cut some 2.5" holes in my VFD enclosure which is .067" thick steel. Any ideas as to the best way to do this? I thought of hole saws but the teeth seem way too coarse for cutting thin metal.
Ed
RE: Cutting Holes In Sheetmatal - Vinny - 05-17-2016
Greenlee punches. HF has a cheapo set but the bolt seems to be made of play dough. I used another bolt with a nut and that worked. Greenlee doesn't have that problem.
RE: Cutting Holes In Sheetmatal - EdK - 05-17-2016
I'm not sure those types of punches will work with that thick of steel. I used to have a set of smaller punch and dies like that and I know they would never work with that thick of steel. But thanks for the suggestion.
Ed
RE: Cutting Holes In Sheetmatal - Vinny - 05-17-2016
I used the cheap HF punches to punch a 480v 75KVA transformer box. Not sure how thick it was.
RE: Cutting Holes In Sheetmatal - f350ca - 05-17-2016
A Greenlee punch would have no trouble with 16 gauge sheet, electrical enclosures seam heavier than that and they cut easily.
Hard to get a smooth cut with a hole saw in thin sheet metal, if you try it take the bit out and use a piece of 1/4 rod, helps some.
2 1/2 might be easier to do with a jig saw.
RE: Cutting Holes In Sheetmatal - Roadracer_Al - 05-17-2016
You could do that with a hand-nibbler, as well.
http://www.amazon.com/Parts-Express-Nickel-Plated-Nibbling/dp/B0002KRACO/ref=sr_1_1?ie=UTF8&qid=1463522317&sr=8-1&keywords=Hand+Nibbler
RE: Cutting Holes In Sheetmatal - EdK - 05-17-2016
(05-17-2016, 04:48 PM)f350ca Wrote: A Greenlee punch would have no trouble with 16 gauge sheet
That's good to know but that's a lot of money to spend for two holes.
Ed
RE: Cutting Holes In Sheetmatal - EdK - 05-17-2016
(05-17-2016, 04:45 PM)Vinny Wrote: I used the cheap HF punches to punch a 480v 75KVA transformer box. Not sure how thick it was.
I'll take a look at the HF version. If it can survive two holes I'll be happy since it'll never get used again.
Ed
RE: Cutting Holes In Sheetmatal - DaveH - 05-17-2016
The way I have done it is to place the part to be cut on a thick piece of wood on the floor. Then stand on it (nicely)
Use an electric hand drill on the slowest rpm with a bit of cutting fluid and 'waggle' the drill in a slow circular motion. Slow and more slow.
The pitch of the teeth is fine - one tooth will travel 8'' along the metal in one revolution.
When I say the pitch of the teeth is fine, I don't mean the physical placement of the teeth is fine, I mean it will be fine to use.
Although the pitch may seem coarse, the application it is being used for the pitch is OK.
DaveH
RE: Cutting Holes In Sheetmatal - TomG - 05-17-2016
For two holes, I would use a sabre saw or just drill a bunch of small holes around the periphery, knock it out and file to make it pretty.
Tom