MetalworkingFun Forum › Machining › General Metalworking Discussion v
Cutting Holes In Sheetmatal

Thread Modes
Cutting Holes In Sheetmatal
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
The following 1 user Likes Dr Stan's post:
DaveH (05-18-2016)
#18
05-17-2016, 10:58 PM
Ditto on pepi's & DaveH's comments.  I'd go with the DP as you'll have much more control over the entire process.

One other option would be a plasma torch & a circle cutter if that is available.
Reply
Thanks given by: EdK


Messages In This Thread
Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:23 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:33 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:40 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:45 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:28 PM
RE: Cutting Holes In Sheetmatal - by f350ca - 05-17-2016, 04:48 PM
RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-17-2016, 04:59 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:27 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-17-2016, 05:40 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-17-2016, 09:55 PM
RE: Cutting Holes In Sheetmatal - by TomG - 05-17-2016, 05:44 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 06:05 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 06:13 PM
RE: Cutting Holes In Sheetmatal - by wawoodman - 05-17-2016, 06:53 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 07:39 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 07:46 PM
RE: Cutting Holes In Sheetmatal - by arvidj - 05-17-2016, 08:46 PM
RE: Cutting Holes In Sheetmatal - by Dr Stan - 05-17-2016, 10:58 PM
RE: Cutting Holes In Sheetmatal - by Hawkeye - 05-17-2016, 11:09 PM
RE: Cutting Holes In Sheetmatal - by awemawson - 05-18-2016, 03:16 AM
RE: Cutting Holes In Sheetmatal - by EdK - 05-18-2016, 05:31 AM
RE: Cutting Holes In Sheetmatal - by rleete - 05-18-2016, 09:01 AM
RE: Cutting Holes In Sheetmatal - by Mayhem - 05-18-2016, 09:29 AM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 07:12 AM
RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-18-2016, 12:01 PM
RE: Cutting Holes In Sheetmatal - by PixMan - 05-18-2016, 01:20 PM
RE: Cutting Holes In Sheetmatal - by dallen - 05-18-2016, 05:50 PM
RE: Cutting Holes In Sheetmatal - by PixMan - 05-19-2016, 06:12 AM
RE: Cutting Holes In Sheetmatal - by the penguin - 05-19-2016, 09:04 AM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 03:28 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 06:10 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 06:49 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 06:57 PM
RE: Cutting Holes In Sheetmetal - by EdK - 05-19-2016, 07:18 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 07:13 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 07:19 PM
RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 08:34 PM
RE: Cutting Holes In Sheetmatal - by EdK - 05-28-2016, 04:26 PM
RE: Cutting Holes In Sheetmatal - by DaveH - 05-28-2016, 06:18 PM
RE: Cutting Holes In Sheetmatal - by Vinny - 05-28-2016, 08:27 PM



Users browsing this thread: 7 Guest(s)