Cutting Holes In Sheetmatal

Thread Modes

Cutting Holes In Sheetmatal

EdK

Whipping Boy

Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota

05-17-2016, 05:27 PM

(05-17-2016, 04:48 PM)f350ca Wrote: A Greenlee punch would have no trouble with 16 gauge sheet

That's good to know but that's a lot of money to spend for two holes. Yikes

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:23 PM

RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:33 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 04:40 PM

RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 04:45 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:28 PM

RE: Cutting Holes In Sheetmatal - by f350ca - 05-17-2016, 04:48 PM

RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-17-2016, 04:59 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 05:27 PM

RE: Cutting Holes In Sheetmatal - by DaveH - 05-17-2016, 05:40 PM

RE: Cutting Holes In Sheetmatal - by pepi - 05-17-2016, 09:55 PM

RE: Cutting Holes In Sheetmatal - by TomG - 05-17-2016, 05:44 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 06:05 PM

RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 06:13 PM

RE: Cutting Holes In Sheetmatal - by wawoodman - 05-17-2016, 06:53 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-17-2016, 07:39 PM

RE: Cutting Holes In Sheetmatal - by Vinny - 05-17-2016, 07:46 PM

RE: Cutting Holes In Sheetmatal - by arvidj - 05-17-2016, 08:46 PM

RE: Cutting Holes In Sheetmatal - by Dr Stan - 05-17-2016, 10:58 PM

RE: Cutting Holes In Sheetmatal - by Hawkeye - 05-17-2016, 11:09 PM

RE: Cutting Holes In Sheetmatal - by awemawson - 05-18-2016, 03:16 AM

RE: Cutting Holes In Sheetmatal - by EdK - 05-18-2016, 05:31 AM

RE: Cutting Holes In Sheetmatal - by rleete - 05-18-2016, 09:01 AM

RE: Cutting Holes In Sheetmatal - by Mayhem - 05-18-2016, 09:29 AM

RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 07:12 AM

RE: Cutting Holes In Sheetmatal - by Roadracer_Al - 05-18-2016, 12:01 PM

RE: Cutting Holes In Sheetmatal - by PixMan - 05-18-2016, 01:20 PM

RE: Cutting Holes In Sheetmatal - by dallen - 05-18-2016, 05:50 PM

RE: Cutting Holes In Sheetmatal - by PixMan - 05-19-2016, 06:12 AM

RE: Cutting Holes In Sheetmatal - by the penguin - 05-19-2016, 09:04 AM

RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 03:28 PM

RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 06:10 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 06:49 PM

RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 06:57 PM

RE: Cutting Holes In Sheetmetal - by EdK - 05-19-2016, 07:18 PM

RE: Cutting Holes In Sheetmatal - by DaveH - 05-19-2016, 07:13 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-19-2016, 07:19 PM

RE: Cutting Holes In Sheetmatal - by pepi - 05-19-2016, 08:34 PM

RE: Cutting Holes In Sheetmatal - by EdK - 05-28-2016, 04:26 PM

RE: Cutting Holes In Sheetmatal - by DaveH - 05-28-2016, 06:18 PM

RE: Cutting Holes In Sheetmatal - by Vinny - 05-28-2016, 08:27 PM

Users browsing this thread: 5 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me