Tooling up a mill

Hello There, Guest! Register

Thread Modes

Tooling up a mill

Mayhem Offline

Offline

purveyor of mischief

Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia

#40

07-01-2014, 09:54 AM (This post was last modified: 07-01-2014, 09:54 AM by Mayhem.)

There is no thread on the end of the MT3 arbour Dave but that chuck will be used in the tailstock on my lathe. The NMBT30 arbour I have for use in my mill has a drawbar thread on it.

Ed - the max RPM is listed as 1500 for that size edge finder on the Fisher web site, so I'll make sure I stay below that. I'll probably just look for the kick.

Hunting American dentists since 2015.

Reply

Thanks given by: DaveH

« Next Oldest | Next Newest »

Messages In This Thread

Tooling up a mill - by Mayhem - 02-22-2012, 08:09 AM

RE: Tooling up a mill - by Highpower - 02-22-2012, 09:04 AM

RE: Tooling up a mill - by DaveH - 02-22-2012, 11:15 AM

RE: Tooling up a mill - by ETC57 - 02-22-2012, 03:20 PM

RE: Tooling up a mill - by DaveH - 03-08-2012, 05:23 PM

RE: Tooling up a mill - by TOM REED - 03-08-2012, 10:07 PM

RE: Tooling up a mill - by Mayhem - 03-08-2012, 11:29 PM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 02:24 AM

RE: Tooling up a mill - by arvidj - 03-09-2012, 11:52 AM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 01:21 PM

RE: Tooling up a mill - by arvidj - 03-09-2012, 02:04 PM

RE: Tooling up a mill - by EdK - 03-09-2012, 02:08 PM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 06:18 PM

RE: Tooling up a mill - by EdK - 03-09-2012, 06:20 PM

RE: Tooling up a mill - by EdK - 03-10-2012, 09:24 AM

RE: Tooling up a mill - by arvidj - 03-10-2012, 09:41 AM

RE: Tooling up a mill - by EdK - 03-10-2012, 09:53 AM

RE: Tooling up a mill - by TOM REED - 03-10-2012, 04:08 PM

RE: Tooling up a mill - by EdK - 03-10-2012, 04:13 PM

RE: Tooling up a mill - by TOM REED - 03-10-2012, 10:02 PM

RE: Tooling up a mill - by EdK - 03-12-2012, 06:00 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 08:26 AM

RE: Tooling up a mill - by EdK - 03-12-2012, 08:41 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 09:02 AM

RE: Tooling up a mill - by Mayhem - 03-12-2012, 08:53 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 09:12 AM

RE: Tooling up a mill - by Hopefuldave - 03-17-2012, 08:08 PM

RE: Tooling up a mill - by EdK - 03-12-2012, 12:23 PM

RE: Tooling up a mill - by arvidj - 03-17-2012, 05:44 PM

RE: Tooling up a mill - by DaveH - 03-17-2012, 05:49 PM

RE: Tooling up a mill - by EdK - 03-17-2012, 06:29 PM

RE: Tooling up a mill - by Mayhem - 03-18-2012, 12:42 AM

RE: Tooling up a mill - by TOM REED - 03-18-2012, 08:09 AM

RE: Tooling up a mill - by EdK - 03-18-2012, 09:06 AM

RE: Tooling up a mill - by Mayhem - 03-18-2012, 08:15 AM

RE: Tooling up a mill - by TOM REED - 03-18-2012, 08:26 AM

RE: Tooling up a mill - by Mayhem - 07-01-2014, 07:31 AM

RE: Tooling up a mill - by EdK - 07-01-2014, 08:34 AM

RE: Tooling up a mill - by DaveH - 07-01-2014, 08:22 AM

RE: Tooling up a mill - by Mayhem - 07-01-2014, 09:54 AM

RE: Tooling up a mill - by PixMan - 07-01-2014, 11:16 AM

RE: Tooling up a mill - by stevec - 07-01-2014, 11:17 AM

Users browsing this thread: 13 Guest(s)