MetalworkingFun Forum › Machining › CNC v
4R8's table build

Thread Modes
4R8's table build
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#20
11-16-2012, 01:42 AM
Jason,
Did you use aluminum tube for the gantry? I picked up 5 feet of 3x3 inch .120 wall for mine. Haven't miked it yet, hoping it will be accurate enough to position the tracks.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
4R8's table build - by 4R8 - 11-13-2012, 09:46 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 10:28 PM
RE: 4R8's table build - by f350ca - 11-13-2012, 10:31 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 11:13 PM
RE: 4R8's table build - by 4R8 - 11-14-2012, 09:40 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:13 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 10:14 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:32 AM
RE: 4R8's table build - by f350ca - 11-14-2012, 10:35 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:51 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 11:01 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:29 AM
RE: 4R8's table build - by stevec - 11-15-2012, 11:46 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:59 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:47 AM
RE: 4R8's table build - by f350ca - 11-15-2012, 01:32 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 02:21 PM
RE: 4R8's table build - by stevec - 11-15-2012, 05:54 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:48 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 01:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 04:23 AM
RE: 4R8's table build - by sasquatch - 11-16-2012, 08:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:13 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:50 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:51 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 05:10 PM
RE: 4R8's table build - by EdK - 11-16-2012, 07:01 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:05 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:06 PM
RE: 4R8's table build - by EdK - 11-19-2012, 05:24 PM
RE: 4R8's table build - by 4R8 - 11-21-2012, 04:11 PM



Users browsing this thread: 4 Guest(s)