MetalworkingFun Forum › Machining › CNC v
4R8's table build

Thread Modes
4R8's table build
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#3
11-13-2012, 10:31 PM
Looking good.
When you say the Y axis is driven from both sides, does that mean two motors?
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
4R8's table build - by 4R8 - 11-13-2012, 09:46 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 10:28 PM
RE: 4R8's table build - by f350ca - 11-13-2012, 10:31 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 11:13 PM
RE: 4R8's table build - by 4R8 - 11-14-2012, 09:40 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:13 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 10:14 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:32 AM
RE: 4R8's table build - by f350ca - 11-14-2012, 10:35 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:51 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 11:01 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:29 AM
RE: 4R8's table build - by stevec - 11-15-2012, 11:46 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:59 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:47 AM
RE: 4R8's table build - by f350ca - 11-15-2012, 01:32 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 02:21 PM
RE: 4R8's table build - by stevec - 11-15-2012, 05:54 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:48 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 01:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 04:23 AM
RE: 4R8's table build - by sasquatch - 11-16-2012, 08:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:13 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:50 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:51 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 05:10 PM
RE: 4R8's table build - by EdK - 11-16-2012, 07:01 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:05 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:06 PM
RE: 4R8's table build - by EdK - 11-19-2012, 05:24 PM
RE: 4R8's table build - by 4R8 - 11-21-2012, 04:11 PM



Users browsing this thread: 5 Guest(s)