Tooling up a mill

Hello There, Guest! Register

Thread Modes

Tooling up a mill

Hopefuldave Offline

Offline

Sophmore

Posts: 168
Threads: 6
Joined: Mar 2012
Location: Surrey, England

#31

03-17-2012, 08:08 PM (This post was last modified: 03-17-2012, 08:34 PM by EdK.)

arvidj Wrote:And based on the picture the thought that "some disassembly will be required" has been confirmed. Based on the 1000m width of the table plus the power feed on one end and the handles on the other cpmpared with the width of the basement door I see a violation of some quantum physics two objects, same time, same space law or another.

Schrodinger's Mill - both inside and outside the 'shop at one time, well known quantum effect...

Dave H. (the other one)

Rules are for the obedience of fools, and the guidance of wise men...
(Douglas Bader)

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Tooling up a mill - by Mayhem - 02-22-2012, 08:09 AM

RE: Tooling up a mill - by Highpower - 02-22-2012, 09:04 AM

RE: Tooling up a mill - by DaveH - 02-22-2012, 11:15 AM

RE: Tooling up a mill - by ETC57 - 02-22-2012, 03:20 PM

RE: Tooling up a mill - by DaveH - 03-08-2012, 05:23 PM

RE: Tooling up a mill - by TOM REED - 03-08-2012, 10:07 PM

RE: Tooling up a mill - by Mayhem - 03-08-2012, 11:29 PM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 02:24 AM

RE: Tooling up a mill - by arvidj - 03-09-2012, 11:52 AM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 01:21 PM

RE: Tooling up a mill - by arvidj - 03-09-2012, 02:04 PM

RE: Tooling up a mill - by EdK - 03-09-2012, 02:08 PM

RE: Tooling up a mill - by TOM REED - 03-09-2012, 06:18 PM

RE: Tooling up a mill - by EdK - 03-09-2012, 06:20 PM

RE: Tooling up a mill - by EdK - 03-10-2012, 09:24 AM

RE: Tooling up a mill - by arvidj - 03-10-2012, 09:41 AM

RE: Tooling up a mill - by EdK - 03-10-2012, 09:53 AM

RE: Tooling up a mill - by TOM REED - 03-10-2012, 04:08 PM

RE: Tooling up a mill - by EdK - 03-10-2012, 04:13 PM

RE: Tooling up a mill - by TOM REED - 03-10-2012, 10:02 PM

RE: Tooling up a mill - by EdK - 03-12-2012, 06:00 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 08:26 AM

RE: Tooling up a mill - by EdK - 03-12-2012, 08:41 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 09:02 AM

RE: Tooling up a mill - by Mayhem - 03-12-2012, 08:53 AM

RE: Tooling up a mill - by arvidj - 03-12-2012, 09:12 AM

RE: Tooling up a mill - by Hopefuldave - 03-17-2012, 08:08 PM

RE: Tooling up a mill - by EdK - 03-12-2012, 12:23 PM

RE: Tooling up a mill - by arvidj - 03-17-2012, 05:44 PM

RE: Tooling up a mill - by DaveH - 03-17-2012, 05:49 PM

RE: Tooling up a mill - by EdK - 03-17-2012, 06:29 PM

RE: Tooling up a mill - by Mayhem - 03-18-2012, 12:42 AM

RE: Tooling up a mill - by TOM REED - 03-18-2012, 08:09 AM

RE: Tooling up a mill - by EdK - 03-18-2012, 09:06 AM

RE: Tooling up a mill - by Mayhem - 03-18-2012, 08:15 AM

RE: Tooling up a mill - by TOM REED - 03-18-2012, 08:26 AM

RE: Tooling up a mill - by Mayhem - 07-01-2014, 07:31 AM

RE: Tooling up a mill - by EdK - 07-01-2014, 08:34 AM

RE: Tooling up a mill - by DaveH - 07-01-2014, 08:22 AM

RE: Tooling up a mill - by Mayhem - 07-01-2014, 09:54 AM

RE: Tooling up a mill - by PixMan - 07-01-2014, 11:16 AM

RE: Tooling up a mill - by stevec - 07-01-2014, 11:17 AM

Users browsing this thread: 9 Guest(s)