Darex M2 manual?
#1
Hiya Folks,
My father in-law took me down into his dungeon last Sunday to get my opinion on what he could sell a tool for. It took him awhile to dig out a Darex M2 drill sharpener.
Long story short... It is now in my dungeon.

Searched around a bit but could not find a manual for it. Does anyone know where a copy can be found?

Alan
Reply
Thanks given by:
#2
I bet Walter could give you a source for the manual. He should respond within a couple of days.

Ed
Reply
Thanks given by:
#3
(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.

Ed

Ed

You have a copy, I am sure as it is on the Disk I sent you.

Alan

I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.

Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
Reply
Thanks given by:
#4
Many Thanks.
Alan

I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.

Walter
[/quote]
Reply
Thanks given by:
#5
(08-30-2012, 09:53 AM)starlight_tools Wrote:
(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.

Ed

Ed

You have a copy, I am sure as it is on the Disk I sent you.

Alan

I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.

Walter

That would mean I'd have to know where I put the disks. I need to find them and take another look at the contents again anyway. I've hardly stepped foot in the shop all summer other than to make sure the lathe isn't rusting due to lack of use.

Ed
Reply
Thanks given by:
#6
(08-30-2012, 12:16 PM)EdK Wrote:
(08-30-2012, 09:53 AM)starlight_tools Wrote:
(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.

Ed

Ed

You have a copy, I am sure as it is on the Disk I sent you.

Alan

I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.

Walter

That would mean I'd have to know where I put the disks. I need to find them and take another look at the contents again anyway. I've hardly stepped foot in the shop all summer other than to make sure the lathe isn't rusting due to lack of use.

Ed

That was a pretty big stack of disks, should not be too hard to find.

Lots of good info on them.

Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
Reply
Thanks given by:
#7
(08-30-2012, 04:29 PM)starlight_tools Wrote: That was a pretty big stack of disks, should not be too hard to find.

Lots of good info on them.

Walter

Found them. I had perused them when you sent them Walter, but now I need to take some time and look at them more thoroughly. There's a lot of good information on those CDs.

Ed
Reply
Thanks given by:
#8
(08-30-2012, 04:52 PM)EdK Wrote:
(08-30-2012, 04:29 PM)starlight_tools Wrote: That was a pretty big stack of disks, should not be too hard to find.

Lots of good info on them.

Walter

Found them. I had perused them when you sent them Walter, but now I need to take some time and look at them more thoroughly. There's a lot of good information on those CDs.

Ed

For what they cost you, there must be some good info in there, LOL

Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
Reply
Thanks given by:




Users browsing this thread: