+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Other Machinery (http://www.metalworkingfun.com/forum-13.html)
+--- Thread: Darex M2 manual? (/thread-761.html)
Darex M2 manual? - miner49r - 08-29-2012
Hiya Folks,
My father in-law took me down into his dungeon last Sunday to get my opinion on what he could sell a tool for. It took him awhile to dig out a Darex M2 drill sharpener.
Long story short... It is now in my dungeon.
Searched around a bit but could not find a manual for it. Does anyone know where a copy can be found?
Alan
RE: Darex M2 manual? - EdK - 08-29-2012
I bet Walter could give you a source for the manual. He should respond within a couple of days.
Ed
RE: Darex M2 manual? - starlight_tools - 08-30-2012
(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.
Ed
Ed
You have a copy, I am sure as it is on the Disk I sent you.
Alan
I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.
Walter
RE: Darex M2 manual? - miner49r - 08-30-2012
Many Thanks.
Alan
I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.
Walter
[/quote]
RE: Darex M2 manual? - EdK - 08-30-2012
(08-30-2012, 09:53 AM)starlight_tools Wrote:(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.
Ed
Ed
You have a copy, I am sure as it is on the Disk I sent you.
Alan
I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.
Walter
That would mean I'd have to know where I put the disks. I need to find them and take another look at the contents again anyway. I've hardly stepped foot in the shop all summer other than to make sure the lathe isn't rusting due to lack of use.
Ed
RE: Darex M2 manual? - starlight_tools - 08-30-2012
(08-30-2012, 12:16 PM)EdK Wrote:(08-30-2012, 09:53 AM)starlight_tools Wrote:(08-29-2012, 07:07 PM)EdK Wrote: I bet Walter could give you a source for the manual. He should respond within a couple of days.
Ed
Ed
You have a copy, I am sure as it is on the Disk I sent you.
Alan
I have a copy of the M2 manual, I will PM you and get your email address so I can send you a copy.
Walter
That would mean I'd have to know where I put the disks. I need to find them and take another look at the contents again anyway. I've hardly stepped foot in the shop all summer other than to make sure the lathe isn't rusting due to lack of use.
Ed
That was a pretty big stack of disks, should not be too hard to find.
Lots of good info on them.
Walter
RE: Darex M2 manual? - EdK - 08-30-2012
(08-30-2012, 04:29 PM)starlight_tools Wrote: That was a pretty big stack of disks, should not be too hard to find.
Lots of good info on them.
Walter
Found them. I had perused them when you sent them Walter, but now I need to take some time and look at them more thoroughly. There's a lot of good information on those CDs.
Ed
RE: Darex M2 manual? - starlight_tools - 08-30-2012
(08-30-2012, 04:52 PM)EdK Wrote:(08-30-2012, 04:29 PM)starlight_tools Wrote: That was a pretty big stack of disks, should not be too hard to find.
Lots of good info on them.
Walter
Found them. I had perused them when you sent them Walter, but now I need to take some time and look at them more thoroughly. There's a lot of good information on those CDs.
Ed
For what they cost you, there must be some good info in there, LOL
Walter