Todays Project - What did you do today?
(02-26-2017, 11:23 AM)rleete Wrote: Thumb, you can get 4' LED bulbs (to fit standard fixtures) from Greenlightdepot.com  Bulbs for ballasts, or ones that bypass it.  Less than $7 a bulb for the ones I got (5000k color, bypass) and shipping is quite reasonable ($11 for 10 bulbs), too.

I won't ever buy another CFL or 4' fluorescent bulb ever again.  LED is soooo much better all around.

Thanks, I'll look into that. DO they have 8' LED bulbs too?
Reply
Thanks given by:
(03-07-2017, 11:33 AM)Thumb Wrote:
(02-26-2017, 11:23 AM)rleete Wrote: Thumb, you can get 4' LED bulbs (to fit standard fixtures) from Greenlightdepot.com  Bulbs for ballasts, or ones that bypass it.  Less than $7 a bulb for the ones I got (5000k color, bypass) and shipping is quite reasonable ($11 for 10 bulbs), too.

I won't ever buy another CFL or 4' fluorescent bulb ever again.  LED is soooo much better all around.

Thanks, I'll look into that. DO they have 8' LED bulbs too?

yes
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
Vinny,

Took a look at the Green Lights web site.  Converting over going to cost me a pretty penny, but it should be well worth the expenditure.  I do have one question, what is the difference in the long run between the two different types of tubes?  Removing & rewiring the fixture should be straight forward.  So is there any real advantage of one over the other?

Thanks,

Stan
Reply
Thanks given by:
I went with the bypass because I have a shorted ballast in one of my downstairs lites. Since all the fixtures are identical, it's worth not bothering with one that needs a ballast - not to mention those are cheaper!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
Bypass bulbs are cheaper, but if you do the bypass (cutting out the ballast), you can not go back to regular fluorescents.

Then again, with the bypass bulbs, even a "dead" fixture can be used.
Full of ideas, but slow to produce parts
Reply
Thanks given by:
So you are saying that the linear bulbs can just be plugged into the fixture without any mods to it?
Reply
Thanks given by:
The ones that say "ballast compatible or bypass" work in any fixture. No mods necessary.
Full of ideas, but slow to produce parts
Reply
Thanks given by:
(03-08-2017, 12:52 PM)rleete Wrote: The ones that say "ballast compatible or bypass" work in any fixture.  No mods necessary.

What does the "bypass" mean? It sounds like one would need to do some rewiring if you were to go with the "bypass' version. 17428

Ed
Reply
Thanks given by:
(03-08-2017, 01:31 PM)EdK Wrote:
(03-08-2017, 12:52 PM)rleete Wrote: The ones that say "ballast compatible or bypass" work in any fixture.  No mods necessary.

What does the "bypass" mean? It sounds like one would need to do some rewiring if you were to go with the "bypass' version.  17428

Ed

Bypass means it bypasses the ballast. If you go to the web page for one of their bypass bulbs, you'll see a link to the how-to on rewiring the fixture. I have a fixture with a shorted ballast so needless to say a bypass bulb is going in there first!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
The strange thing is that in most cases, a replacement ballast costs more than a new fixture. But, when you have a factory full of hardwired fixtures, replacing the ballast is a hell of a lot easier.
Mike

SB 10K (1976) Rockwell vertical mill (1967) Rockwell 17" drill press (1946) Me (1949)
Reply
Thanks given by:




Users browsing this thread: 10 Guest(s)