Setting Up KOC100 VFD
#11
Mike, don't want to hijack your thread and question, just a quick question on my part. Is it normal to need such long start up times with VFD's?
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#12
Greg, my guess is a VFD is designed for run current. The instant inrush of current to start a motor is more than one can handle based on it's usage ratings. Any motor has a high inrush if started on the mains. Think of the momentary dimming of the lights when a well pump or compressor starts, and thats ON the mains.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by: f350ca
#13
Ten seconds is the factory default on most of the VFDs that I've worked with. I usually change it to five seconds and haven't had any problems.  Smiley-gen163

Ed
Reply
Thanks given by: f350ca
#14
I can set my accel and decel times down to 1/2 second and the lathe motor will start and stop in that time once I got all the parameters set correctly. The only 'problem' with setting the times so short is that the weight/mass of the spindle/chuck and drive train can't keep up with the motor and it will squeal the drive belt. Sort of akin to getting a fully loaded freight train rolling from a dead stop, or trying to stop one (quickly) when it's at full speed.
Willie
Reply
Thanks given by:
#15
It doesn't seem to make any difference how I set the ramps times. Sometimes, if I've disconnected and reconnected, the auto-tune will go far enough to run the motor (the manual says up to 80%) but always returns an error message.

I did megger the cable and motor. The lowest it would go on any lead is 186 Meg-ohms at 500 VDC. Plenty solid enough.

Let's see if I can insert the manual here ...


.pdf   KOC100 Series User Manual--20150323(V1.1).pdf (Size: 2.97 MB / Downloads: 10)

Good. This should let you generate plenty of questions. I took the week off and have pretty much wasted it on messing with this VFD. (That and picking up a Roland TD-12 drum kit.)
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
#16
Data plate info on the motor you want to use? 17428
List of any parameters you have changed from their defaults?

Always best to start at the beginning and the simple stuff that is easily overlooked IMO.
Willie
Reply
Thanks given by:
#17
Mike,

I assume you have a typo in your first post. The manual says you should be setting "d0-30/d3-30 to 2". Not "b0-30" as your post shows.

Ed

   
Reply
Thanks given by:
#18
Motor Info as entered:

b0-00: 0 (Asynchronous motor)
d0-00: 1.5 KW
d0-01: 240 (tried 220 and 230 as well)
d0-02: 6.2 amps
d0-03: 60 Hz
d0-04: 1740 RPM

Additional parameters:

b0-12: 60
b0-13: 60
b0-14: 0 (default)
b0-15: 60
b0-21: 10 (tried 4 to 25 - no change)
b0-22: 10 (tried 4 to 25 - no change)

All other settings are left at default, including those relating to the remote console. The VFD responds to its own front panel only.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
#19
I massaged the manual that Mike posted so it can be searched using Acrobat Reader.

Ed


Attached Files
.pdf   KOC100 Series User Manual--20150323(V1.1).pdf (Size: 2.06 MB / Downloads: 6)
Reply
Thanks given by: Highpower
#20
Mike, is D2-01 set at 0.0?   Chin
Willie
Reply
Thanks given by:




Users browsing this thread: 4 Guest(s)