MetalworkingFun Forum › Machinery › Milling Machines v
Setting Up My PM935 Mill

Thread Modes
Setting Up My PM935 Mill
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 2 users Like EdK's post:
Mayhem (11-01-2015), arvidj (11-01-2015)
#181
11-01-2015, 12:18 PM
Got'r done. On to the next phase which will be the wiring.

Ed

   
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#182
11-01-2015, 12:57 PM
move the hole in the plate for the eye bolt towards the back of the lathe which will move the balance point so that you don't have to take the motor off again
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#183
11-01-2015, 01:08 PM
Taking the motor off didn't help much so I came up with a different solution that worked, and was a whole lot simpler.

You make a good point though. I'll have to remember that if I ever have to move the lathe again.

Ed
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#184
11-01-2015, 01:34 PM
Good job Ed,  Thumbsup  although it looks easy from here Big Grin 
Smiley-eatdrink004 
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by: EdK
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#185
11-01-2015, 05:35 PM
Bird's eye view.  Smile

I still have to figure out where the shop press is going to reside. Chin

Ed

   
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#186
11-02-2015, 02:40 PM
(11-01-2015, 05:35 PM)EdK Wrote: Bird's eye view.  Smile

I still have to figure out where the shop press is going to reside.  Chin

Ed

Back end of the garage? It's not metal cutting (usually), won't make a mess (usually) and takes up little space for an infrequently used tool. The milling machine will get FAR more use.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#187
11-02-2015, 03:04 PM
(11-02-2015, 02:40 PM)PixMan Wrote:
(11-01-2015, 05:35 PM)EdK Wrote: Bird's eye view.  Smile

I still have to figure out where the shop press is going to reside.  Chin

Ed

Back end of the garage? It's not metal cutting (usually), won't make a mess (usually) and takes up little space for an infrequently used tool. The milling machine will get FAR more use.

I was thinking the same thing Ken. Thumbsup

Ed
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 5 users Like EdK's post:
Mayhem (11-02-2015), f350ca (11-02-2015), PixMan (11-02-2015), wrustle (11-02-2015), Highpower (11-02-2015)
#188
11-02-2015, 05:19 PM
Got the lathe light and power wiring moved over so the lathe is now usable. That is after I give it a good cleaning before I reattach the back splash and motor.  Smile
Amazing how long it took to move the light and wiring. I guess I'm getting slower as I plunge deep into oldicis farticis.

Ed

   
Reply
Thanks given by:
wrustle Offline
Junior
****
Posts: 438
Threads: 67
Joined: Sep 2012
Location: Central Mass.
The following 1 user Likes wrustle's post:
Mayhem (11-03-2015)
#189
11-02-2015, 07:14 PM
Correct me if I'm wrong......but..........isn't this a "Milling Machine" thread???

COME ON ED......LET'S SEE SOME CHIPS!!!
Best Regards,
Russ

Check us out on Facebook and give us a "Like" 

Crosby Machine Company, Inc

Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 2 users Like EdK's post:
Mayhem (11-03-2015), wrustle (11-03-2015)
#190
11-02-2015, 07:24 PM
(11-02-2015, 07:14 PM)wrustle Wrote: Correct me if I'm wrong......but..........isn't this a "Milling Machine" thread???

COME ON ED......LET'S SEE SOME CHIPS!!!

Russ,

What the hell, do you not like foreplay? 17428

Ed
Reply
Thanks given by:




Users browsing this thread: 41 Guest(s)