MetalworkingFun Forum › Machining › CNC v
Converting a X2 clone to CNC

Thread Modes
Converting a X2 clone to CNC
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#81
05-29-2014, 08:04 PM
Smiley-signs009
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
The following 1 user Likes Shawn's post:
EdK (05-30-2014)
#82
05-30-2014, 01:51 PM
Thanks guys. Spent a bit more time this morning playing with the setup. I thing the bit was slipping in the collet yesterday? .002"doc, 7ipm feed and 54,000rpm. The top engraving was done with a very fine endmill .5mm? The second was cut with a three sided 30 degree tool. The engraving is .135" tall on aluminium plate. I did flatten the stock on my shaper to make sure there wasn't an issue with surface irregularity.

[Image: image.jpg]

Shawn
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
#83
05-30-2014, 01:59 PM
And yes my girlfriends last name is Steele Cool
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#84
05-31-2014, 05:07 AM
I'd love to see that 3 sided 30° tool. Rotfl
Nice looking engraving Shawn. Thumbsup
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#85
05-31-2014, 12:05 PM
Very nice Shawn,
54000 rpm that's quick Yikes
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
The following 1 user Likes Shawn's post:
EdK (05-31-2014)
#86
05-31-2014, 12:30 PM
Thanks guys

The grinder is advertised as 54,000 rpm but I have no real idea how fast it is. I can't tell the difference in the engraving between the lowest and highest setting so I just use the low speed to save on air.

Steve, these are similar to the bits I'm have, I ordered mine from china and they were cheap but I only plan to engrave plastic and aluminum.

[Image: 10-pcs-3-175-30-0-2MM-3-Edge-Cutting-Too...raving.jpg]

Shawn
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by: stevec
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#87
05-31-2014, 03:32 PM
They look nicely made Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 5 Guest(s)