+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: CNC (http://www.metalworkingfun.com/forum-28.html)
+--- Thread: Converting a X2 clone to CNC (/thread-1913.html)
Converting a X2 clone to CNC - Shawn - 12-19-2013
Hey guys, the electronics and Fusion CNC conversion kit I ordered has finally arrived for my Busy Bee X2. Over the next few weeks I will be converting it over to Cnc and will use this post to update and ask questions. I have removed the spring balance and replaced it with a counter weight many months ago in preparation for the conversion so that part is already done, I also converted it to belt drive at the same time.
The first of many photos, this was taken shortly after buying the mill.
![[Image: qr0o.jpg]](http://img703.imageshack.us/img703/1033/qr0o.jpg)
Shawn
RE: Converting a X2 clone to CNC - Hawkeye - 12-20-2013
Shawn, if you get the chance, increase the Y-axis travel. I added almost 2" to mine, but I wish I'd added more.
The X2 mills make great little CNCs. I haven't done a lot on mine, but it's fun to watch it following a program I put together. Sometimes there are
moments, but that's all part of the learning process.
RE: Converting a X2 clone to CNC - Shawn - 12-20-2013
I remember seeing the photos you posted Mike of the extension you built, that would be a great mod to make. It will have to be further done the road for me, I already have the ball screw. The CNC Fusion Kit is really nicely done and I think its great value for the price. The casting on my mill is another story, it's going to require some modifications to allow the axis to fit without binding. I can see where a real newby could get quickly overwhelmed trying to install the kit.
Shawn
RE: Converting a X2 clone to CNC - Shawn - 12-20-2013
The irony of using the most outdated tool in my shop to build the most technically advanced tool was not lost on me
I had to remove .125 from the side of the mounting block so the plate that mounts to the column would line up properly.![[Image: 3uvo.jpg]](http://img823.imageshack.us/img823/3291/3uvo.jpg)
The Z axis is installed and runs smoothly from top to bottom with no hint of binding. I did have to grind a bolt down (it was either that or enlarge a hole in the casting) but otherwise the Fusion kit fit better than I expected considering how many variations there are of these mills and how poor the casting quality can be. I'll finish up the other two axis tomorrow, I don't think they should require as much finagling.
![[Image: k8p6.jpg]](http://img10.imageshack.us/img10/2368/k8p6.jpg)
Shawn
RE: Converting a X2 clone to CNC - Shawn - 12-21-2013
So I actually finished the other two axis last night. Only took an hour or so and everything fit nicely accept for the two cap head screws that hold the x axis lead screw nut in place. The heads needed to be cut off and a slit cut for a flat head screwdriver. Now I just have to figure out how all this gets wired up. That will have to wait till after the holidays though.
One question about my counterweight setup; the head is almost perfectly balanced, it takes the same pressure to lift it as it does to lower it. Will this be an issue when cutting? Do I want more downward pressure on the head or should the steppers be able to hold it?
![[Image: zy6x.jpg]](http://img707.imageshack.us/img707/149/zy6x.jpg)
Shawn
RE: Converting a X2 clone to CNC - Shawn - 12-22-2013
I didn't have much time today but did manage to build some swarf guards for the Y and Z axis. The Y axis is held in place with two magnets so accessing the lead screw is simple, the Z axis was boxed in as much as the casting would allow and is held in place with a single cap screw. I had never worked with aluminum sheet and a brake before but I can see that being incredibly useful in the future. Limit switches and the wiring left to go.
![[Image: 0w58.jpg]](http://img542.imageshack.us/img542/3459/0w58.jpg)
![[Image: lob9.jpg]](http://img571.imageshack.us/img571/2761/lob9.jpg)
Shawn
RE: Converting a X2 clone to CNC - Shawn - 12-25-2013
Being a closet computer geek I was pretty pleased to see a computer setup in my machine shop (I like that better than saying garage)
![[Image: d18e.jpg]](http://img839.imageshack.us/img839/632/d18e.jpg)
Shawn
RE: Converting a X2 clone to CNC - wrustle - 12-27-2013
Shawn!
Looking good, and even better, making progress!!
Can't wait to see some chips flying!
Best Regards,
Russ
RE: Converting a X2 clone to CNC - Shawn - 12-27-2013
Thanks Russ, I'm just waiting on some 18/4 shielded wire and an emergency stop button to arrive in the mail. I bought a small tool box today on sale and will convert that to hold the power supply, breakout board etc. I'm hoping to see it in action soon, I do have a backlash issue with one of the ball nuts but hopefully the company will respond to my email soon and we can get that sorted. I don't think its a preload issue but I might be wrong?
RE: Converting a X2 clone to CNC - Hawkeye - 12-27-2013
I saw an item on the net once that mentioned replacing the balls with a size bigger to tighten it up. Apparently, you can order loose ball bearings in very specific sizes.