Carbide Grinder
#21
You got off easy on the last order Tom, just average the two and it won't seem as bad.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#22
(09-21-2012, 05:49 AM)Highpower Wrote: ...It threw me a couple of times because it even shows up as MSC on my credit card statement!

PM me with your credit card details Willie (number, name, exp date, code) and I'll run a check to ensure you are not going to be a victim of credit card fraud, which can happen when things like this happen Angel
Hunting American dentists since 2015.
Reply
Thanks given by:
#23
righgt my name is tommy tucker not stupid ------ tom

however over my 44 or so of using my credit card for everything my wife checks + verifys my every statement, there have been a few unauthorized purchases she has discovered, also there have been several charges over the years that have never shown up either.
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#24
(09-30-2012, 10:40 AM)TOM REED Wrote: my wife checks + verifys my every statement, there have been a few unauthorized purchases she has discovered,
Just wondering Tom, ole Bud, were those "unauthorized purchases" made by you?RotflSmiley-dancenanaRotfl
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#25
(09-30-2012, 09:59 AM)Mayhem Wrote: PM me with your credit card details Willie (number, name, exp date, code) and I'll run a check to ensure you are not going to be a victim of credit card fraud, which can happen when things like this happen Angel

Too late Darren, I've already had that pleasure once. Fortunately my bank was very cooperative in dismissing the charges and setting me up with a new account.

Apparently I purchased a couple of gift subscriptions to some "gentlemen's magazines" for someone in the UK. Chin

Rotfl Rotfl Rotfl
Willie
Reply
Thanks given by:
#26
The fraud department put a hold on my credit card last week because I made a "suspicious" purchase totaling $6.95 at Hemley Tool in CT. They didn't call my wife to check, simply put a hold on the card. As my wife was unaware, she went to get money out of the ATM and the machine ate her card and told her to call the bank! We now have to have new cards issued.

This is after they blocked me from withdrawing cash from any ATM in the US (for some stupid reason), which is why I had to put such a small amount on the credit card to begin with.

So much for calling them ahead of time and telling them I will be traveling to the US and using my plastic whilst I am there Rant
Hunting American dentists since 2015.
Reply
Thanks given by:
#27
What a pain Darren! My dad can't use his debit card at Walmart in El Paso Rotfl He can use it at the gas station across the street but his bank always blocks purchases from the Walmart Rotfl
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
Reply
Thanks given by:
#28
Oh my! I can't believe that happened to you. I would down at that bank insisting they make my old cards good again, though I know well how futile that can be.
Reply
Thanks given by:
#29
Grinder arrived this week, it is fairly good and runs well without shake, wheels probably need truing but it will do a much better job than "I can do freehand so on the whole I am happy. Only problem I was quoted $125.00 by FEDEX GROUND for shipping to my door. this was all set up all ENCO was to do was call FEDEX GROUND for pickup. Instead ENCO called FEDEX FREIGHT, and there the problem begins, FEDEX FREIGHT does not clear customs so I had to have broker clear for me which cost me an additional $100.00, now it gets to CALGARY and FEDEX FREIGHT informs me the shipping charges are $250.00 and they tell me this is based on the size and weight which are much greater than the grinder. The parcel arrived on WED and it was obvious why the charges were more ENCO strapped the damn carton to a small pallet. So the long and short of it my deal of $212.00 for the grinder but I really got the shaft on shipping and brokerage which made my landed cost $575.00. Thanks ENCO for really screwing up my order, I will never purchase from them again. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#30
I'd be going back to Enco and telling them that they should meet the additional cost incurred due to their incompetence. Was the instruction and agreement by Enco to us FedEx ground done over the phone or by email?
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: 10 Guest(s)